Vices, dividers and tables

Branded CNC machine vise with hydraulic pressure. Width of the jaws: according to the selected variant Additional dimensions and parameters - see the attached catalog sheet or product description for individual variants The opening can be adjusted using a pin to 4 positions - see the attached catalog sheet The clamping stop (clamping force) can be adjusted - there is a ring with a scale on the handle, which can be pushed against the vise by loosening two Allen screws and thus always achieve a constant tightening force for all workpieces. We recommend purchasing a pressure gauge with the vise, thanks to which you can always adjust the clamping force as needed. The screw is encapsulated -> protection against dust, chips and dirt. The vise bed is open. The body is made of high-quality and highly resistant ductile cast iron FCD60 Use hydraulic oil #68 (PARAMO HM 68 or other hydraulic oil with a viscosity of 68) Clamps (4 pcs), guide stones (2 pcs), handle are also part of the delivery.

Tilting table with T-nut grooves Hob size: according to the selected variant Other dimensions - see the attached catalog sheet Tilt: 0-90°

Branded CNC machine vise with improved hydraulic transmission Width of the jaws: according to the selected variant Additional dimensions and parameters - see the attached catalog sheet or product description for individual variants There is a tightening scale (3 degrees) on the shaft near the booster. Hydraulic transmission can be switched off and tightened manually without it. Just disconnect the nut - see the attached photo. Compared to the VNC series of vices, the VMC type has higher rigidity, the bed is covered from above and from the handle - it prevents chips from getting inside. Vise height guarantee. The mechanism pulls the jaw down when tightening. The screw is encapsulated -> protection against dust, chips and dirt. The body is made of high-quality and highly resistant ductile cast iron FCD60 Bearing surface for workpiece hardened > 45 HRC. Parallelism of the seating surface and the bottom of the vice: 0.01 mm / 100 mm Rectangularity of the seating surface with jaws: 0.02 mm / 100 mm Parallelism of the bearing surface with the workpiece: 0.02 mm / 100 mm Use hydraulic oil #68 (PARAMO HM 68 or other hydraulic oil with a viscosity of 68) Clamps (4 pcs), guide stones (2 pcs), handle are also part of the delivery.

Machine vice type MC with mechanical booster, suitable for MC / NC machines Width of the jaws: according to the selected variant Additional dimensions and parameters - see the attached catalog sheet or product description for individual variants The screw is encapsulated -> protection of the screw against the ingress of dust, chips and dirt. Guarantee height of vices within 0.02mm tolerance The mechanism pulls the jaw down when tightening. The body is made of high-quality and highly resistant ductile cast iron FCD60 Bearing surface for workpiece hardened > 45 HRC. Parallelism of the seating surface and the bottom of the vice: 0.01 mm / 100 mm Rectangularity of the seating surface with jaws: 0.02 mm / 100 mm Parallelism of the bearing surface with the workpiece: 0.02 mm / 100 mm Clamps (4 pcs), guide stones (2 pcs), handle and transport eyes (2 pcs) are also part of the delivery. It is possible to purchase soft and hard jaws for the vise - see attached catalog.

Machine hydraulic vice type MC with hydraulic booster, suitable for MC / NC machines Width of the jaws: according to the selected variant Additional dimensions and parameters - see the attached catalog sheet or product description for individual variants The screw is encapsulated -> protection of the screw against the ingress of dust, chips and dirt. Guarantee height of vices within 0.02mm tolerance The mechanism pulls the jaw down when tightening. The body is made of high-quality and highly resistant ductile cast iron FCD60 Bearing surface for workpiece hardened > 45 HRC. Parallelism of the seating surface and the bottom of the vice: 0.01 mm / 100 mm Rectangularity of the seating surface with jaws: 0.02 mm / 100 mm Parallelism of the bearing surface with the workpiece: 0.02 mm / 100 mm Clamps (4 pcs), guide stones (2 pcs), handle and transport eyes (2 pcs) are also part of the delivery. It is possible to purchase soft and hard jaws for the vise - see attached catalog. Use hydraulic oil #68 (PARAMO HM 68 or other hydraulic oil with a viscosity of 68)

Machine right hydraulic vice type MC, suitable for MC / NC machines, with prismatic jaw Width of the jaws: according to the selected variant Additional dimensions and parameters - see the attached catalog sheet or product description for individual variants Vise for vertical clamping of the workpiece The vise has a ground seating surface with a groove for guide stones on the side. The screw is encapsulated -> protection of the screw against the ingress of dust, chips and dirt. Guarantee height of vices within 0.02mm tolerance The mechanism pulls the jaw down when tightening. The body is made of high-quality and highly resistant ductile cast iron FCD60 Bearing surface for workpiece hardened > 45 HRC. Parallelism of the seating surface and the bottom of the vice: 0.01 mm / 100 mm Rectangularity of the seating surface with jaws: 0.02 mm / 100 mm Parallelism of the bearing surface with the workpiece: 0.02 mm / 100 mm Clamps (4 pcs), guide stones (2 pcs), handle and transport eyes (2 pcs) are also part of the delivery. Use hydraulic oil #68 (PARAMO HM 68 or other hydraulic oil with a viscosity of 68)

Machine hydraulic vice type MC with hydraulic booster, suitable for MC / NC machines Width of the jaws: according to the selected variant Additional dimensions and parameters - see the attached catalog sheet or product description for individual variants The vise has 3 adjustable tightening stages. The screw is encapsulated -> protection of the screw against the ingress of dust, chips and dirt. Guarantee height of vices within 0.02mm tolerance The mechanism pulls the jaw down when tightening. The body is made of high-quality and highly resistant ductile cast iron FCD60 Bearing surface for workpiece hardened > 45 HRC. Parallelism of the seating surface and the bottom of the vice: 0.01 mm / 100 mm Rectangularity of the seating surface with jaws: 0.02 mm / 100 mm Parallelism of the bearing surface with the workpiece: 0.02 mm / 100 mm Clamps (4 pcs), guide stones (2 pcs), handle and transport eyes (2 pcs) are also part of the delivery. Use hydraulic oil #68 (PARAMO HM 68 or other hydraulic oil with a viscosity of 68)

CNC machine vice with pneumatic clamping, suitable for series production Width of the jaws: according to the selected variant Additional dimensions and parameters - see the attached catalog sheet or product description for individual variants The mechanism pulls the jaw down when tightening, preventing the jaw and workpiece from lifting. The body is made of high-quality and highly resistant ductile cast iron FCD60 Bearing surface for workpiece hardened > 45 HRC. Clamps (4 pcs), guide stones (2 pcs), handle are also part of the delivery. Features: The workpiece can be clamped very quickly - with a safe distance of up to 8 mm, the workpiece is clamped within 1.5 seconds. Clamping pressure: up to 8 bar (to achieve a lower clamping force, just reduce the pressure as needed) If the pressure hose flies out, the vise does not loosen - it remains tight.

High precision grinding tool inspection self-centering vice - suitable for 4-axis and 5-axis CNC Width of the jaws: according to the selected variant Additional dimensions and parameters - see the attached catalog sheet or product description for individual variants Hardened and ground jaws, HRC 55 Vise material: cast iron, sliding surfaces HRC 45 Usage: For grinding and inspection, serial and piece production on NC milling machines and machining centers

Machine precision modular vice Width of the jaws: according to the selected variant Max. opening: according to the selected variant Other dimensions - see attached catalog sheet or product description for individual variants

Clamping plate with T grooves for clamping Dimensions: according to the selected variant T-slot: according to the selected variant Other dimensions - see the attached catalog sheet The plate is used for precise clamping of the object during machining Material: High-strength cast iron Grinded functional surfaces with flatness up to 0.02mm / 300mm Boards are made to order, design the clamping holes and their placement yourself - it will be made according to your drawing.

Split modular vice Width of the jaws: according to the selected variant Additional dimensions and parameters - see product description for individual variants Opening: variable - according to the clamping distance on the machine's worktop Material: alloyed tool steel Hardened and ground lines. Modular vise for serial and piece production on CNC milling machines and machining centers. Especially suitable for the production of tools, molds and preparations.