Homepage Clamping tools Clamping accessories

Clamping accessories

Product count: 184
  • Nut for T-slot, ČSN 021529 / DIN 508

    Nut for T-slot, ČSN 021529 / DIN 508

    T-slot nut Dimension of the T-slot: according to the selected variant (dimension "A" - see attached photo) Thread size: according to the selected variant Dimensions of the nut: - see product description for individual variants Standard: ČSN 02 1529 / CSN021529 or DIN508 Material: Structural steel 12050 (C45), heat treated - unless otherwise specified for a specific dimension

    from 2,01 € with VAT
  • Nut for T-slot , bevelled DIN510

    Nut for T-slot , bevelled DIN510

    T-slot beveled nut, beveled - rhombus For deployment from above Dimension of the T-slot: according to the selected variant (dimension "A" - see attached photo) Thread size: according to the selected variant Dimension of the nut: see product description for individual variants Due to the reduced bearing surface in the T-groove, the load capacity is lower than for comparable sizes DIN 508 / ČSN 021529

    from 2,42 € with VAT
  • T-slot clamping screw , ČSN 021124

    T-slot clamping screw , ČSN 021124

    Clamping screw for T slot Thread: according to the selected variant Length L (without square): depending on the selected variant Other dimensions - see product description for individual variants Standard: ČSN 02 1124 Screw strength 10.9, blackened (unless otherwise stated)

    from 4,22 € with VAT
  • Screw studs , HRC27

    Screw studs , HRC27

    Screw double-sided thread - pin Size: according to the selected variant Total length: according to the selected variant Other dimensions - see the attached catalog sheet Strength screw, HRC 27° Suitable for machine use for clamps/bridges/nuts, not suitable for use in auto-moto

    from 1,31 € with VAT
  • Driving carrier , type VDC

    Driving carrier , type VDC

    The driving heart is used for turning the workpiece when clamped between the tips For diameters: according to the selected variant Suitable for grinding or turning between points The drifting of the object is done via an eccentric lever. The front is engaged by a spring, the eccentric lever rests against a pin stop on the lathe flange - see attached catalog sheet.

    from 20,21 € with VAT
  • Control pad with clamp

    Control pad with clamp

    V-cube with yoke - 1pc, control drawing prism cube with yoke Prism length: according to the selected variant Cube width: according to the selected variant Dice height: according to the selected variant Clamping range: see product description for individual variants DIN876/1

    from 29,12 € with VAT
  • Screw studs DIN6379 , AMF

    Screw studs DIN6379 , AMF

    Clamping screw - pin - self-tapping screw, with asymmetric thread length Size: according to the selected variant Total length: according to the selected variant Other dimensions - see the attached catalog sheet Material: hardened steel * M6-M12 for strength 10.9 * M14-M42 for strength 8.8. Threads are rolled, surface treatment - blackening Made according to standard: DIN6379

    from 1,04 € with VAT
  • Precision tilting V-cube with scale

    Precision tilting V-cube with scale

    Tilting control prism V-cube / prismatic adjustable angle Prism width x cube height x cube length: according to the selected variant Locking at the selected angle, setting according to the minute scale The angle setting range is 90°.

    from 56,80 € with VAT
  • Step clamp for clamping parts, vices, fixtures etc.

    Step clamp for clamping parts, vices, fixtures etc.

    Clamp for clamping parts, vices, fixtures, etc. For screw(s): according to the selected variant Total length: according to the selected variant Dimensions: see attached catalog sheet For use with a milling machine, drill, etc. Hardness: HRC 37

    from 4,28 € with VAT
  • Adjustable clamp with thread, ČSN 243651B

    Adjustable clamp with thread, ČSN 243651B

    Adjustable clamp with thread for clamping parts, vise, fixtures, etc. Groove width: according to the selected variant Total length: according to the selected variant Thread: according to the selected variant Dimensions: see product description for individual variants Standard: ČSN 243651 B / replacement for DIN 6316 Strength: 8.8, blackened

    from 20,13 € with VAT
  • Support screw for adjustable clamp , CSN 243651C

    Support screw for adjustable clamp , CSN 243651C

    Support screw for adjustable clamp ČSN 243651B Thread: according to the selected variant Other dimensions - see product description for individual variants Standard: ČSN 243651 C Strength: 8.8, blackened

    from 4,74 € with VAT
  • Adjustable clamp with support screw, CSN 243651B / DIN6316 , AMF

    Adjustable clamp with support screw, CSN 243651B / DIN6316 , AMF

    Clamp for screw with thread and support screw Groove width: according to the selected variant Total length: according to the selected variant Thread / screw: according to the selected variant Other dimensions - see the attached catalog sheet Standard: ČSN 243651 B / DIN 6316 Material: Lacquered hardened steel

    from 34,79 € with VAT

Free shipping

There is possibility of free shipping. For more information click here.

Fast shipping

If on stock, you will recieve your order in 1 working day.

Store

Most of the goods are available at the shop.

Individual discounts

Are you a loyal customer or do you want to become one? Contact us!

Clamping accessories