Magnet. clamps, demagnetizers

Permanent neodymium magnet Maxgrip stands out above all for its high clamping force and versatility. Combination of a pole plate with a relatively fine parallel arrangement of poles. The possibility of continuously regulating the clamping force facilitates the centering of workpieces during turning and grinding. Diameter of the magnet: according to the selected variant Other dimensions - see the attached catalog sheet. Nominal clamping force: 160N/cm2 Pole spacing: 11mm steel, 4mm epoxy Very powerful double neodymium magnet system, steel base. Unique construction with a screw self-locking switching mechanism for smooth adjustment of the clamping force, which facilitates the centering of the workpiece. Very safe, self-locking mechanism preventing the clamp from turning off during machining. Recesses and threads from the underside of the base for clamping to a suitable flange. Usage: turning, round grinding The clamp is equipped with high-quality permanent neodymium magnets, we provide full warranty and post-warranty service for the magnets. A big advantage of the clamp is the patented switching mechanism, which allows you to variably set the clamping force and firmly fixes the set clamping force in any position. Thanks to the switching mechanism, you turn on the clamp at 10 to 20% of the force, easily center the workpiece, switch to 100% and proceed to a safe operation. Cat. no. : MAXG If you are not sure about the choice - you don't know which magnet is suitable for your work, contact us, we will be happy to help!

Branded - Czech - lifting magnet, also for circular materials Model / max. load capacity: according to the selected variant Load capacity for flat material: according to the selected variant Load capacity for circular material: see product description for individual variants or see catalog sheet Min./Max. diameter of circular material: see product description for individual variants or see catalog sheet *for more see the attached capacity table (PDF) below Meets safety factor 3+ (according to EN 13155), so in the tear-off test it can withstand more than three times its maximum permitted load capacity Air gap test - the tear-off test is performed with an air gap -> higher safety in real operating conditions Warranty 5 years for the magnetic system Robust hanging eye made of stainless steel Capacity table for easy orientation directly on the magnet body Simple operation - the load magnet can be switched easily, quickly and safely. Compact body with only two recessed screws The body of the magnet is highly resistant to mechanical damage, the bearings are secured, so their service life is longer. The magnet has a universal eye design for easy hanging. The magnet enables the handling of loads with a maximum temperature of 80°C Usage : Lifting of profiles and sheets - flat, round and cylindrical workpieces Package includes: * Magnet with label * Instructions for use * Certificate We also provide service, tear tests and certification of load magnets - either directly on site or externally.

Branded - Czech - lifting magnet, also for circular materials - for handling hot materials - blanks, forgings, tools, workpieces, sheets, profiles, pipes, etc. It is characterized by high resistance for operation in difficult conditions and enables handling of loads with a temperature of up to 180°C. Model / max. load capacity: according to the selected variant Load capacity for flat material: according to the selected variant Load capacity for circular material: see product description for individual variants or see catalog sheet Min./Max. diameter of circular material: see product description for individual variants or see catalog sheet *for more see the attached capacity table (PDF) below Meets safety factor 3+ (according to EN 13155), so in the tear-off test it can withstand more than three times its maximum permitted load capacity Air gap test - the tear-off test is performed with an air gap -> higher safety in real operating conditions Double magnetic circuit with strong neodymium magnets Warranty 5 years for the magnetic system Robust hanging eye made of stainless steel Capacity table for easy orientation directly on the magnet body Simple operation - the load magnet can be switched easily, quickly and safely with one hand Compact body with only two recessed screws The body of the magnet is highly resistant to mechanical damage, the bearings are secured, so their service life is longer. The magnet has a universal eye design for easy hanging. The magnet enables the handling of loads with a maximum temperature of 180°C Usage : Lifting of profiles and sheets - flat, round and cylindrical workpieces Package includes: * Magnet with label * Instructions for use * Certificate We also provide service, tear tests and certification of load magnets - either directly on s

Lamella magnetic block, induction pads Suitable for permanent magnets and electromagnets. Width x Length x Height: according to the selected variant Pole pitch: 3mm steel, 1mm brass The minimum order quantity is 1-3 pieces depending on the size. Contact us for more information. Lamella blocks make it possible to create an optimal clamping surface for workpieces that, due to their shape, cannot be clamped on the classic surface of a magnetic clamping plate. It is also used to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the clamped workpiece. Another advantage is the possibility of additional processing (machining) of this block for differently shaped workpieces. Compared to cheap lamellar blocks from other manufacturers (e.g. Vertex), these blocks are not glued, but soldered - in significantly higher quality. Blocks can be cut in half and modified according to current needs.

Lamella magnetic block, induction pads Suitable for permanent magnets and electromagnets. Width x Length x Height: according to the selected variant Pole pitch: 3mm steel, 1mm brass The minimum order quantity is 1-3 pieces depending on the size. Contact us for more information. Lamella blocks make it possible to create an optimal clamping surface for workpieces that, due to their shape, cannot be clamped on the classic surface of a magnetic clamping plate. It is also used to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the clamped workpiece. Another advantage is the possibility of additional processing (machining) of this block for differently shaped workpieces. Compared to cheap lamellar blocks from other manufacturers (e.g. Vertex), these blocks are not glued, but soldered - in significantly higher quality. Blocks can be cut in half and modified according to current needs.

Lamella magnetic block, induction pads Pole spacing: Suitable for permanent magnets and electromagnets. Width: 35mm Height: 16mm Length: 60mm The lamellar blocks allow you to create an optimal clamping surface for workpieces that, due to their shape, cannot be clamped on the classic surface of the magnetic clamping plate . It is also used to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the clamped workpiece. Another advantage is the possibility of additional processing (machining) of this block for differently shaped workpieces. Order no. no.: 2015-400

Lamel Magnetic Block Polar Pitch: 2,5 3mm Suitable for permanent magnets and electromagnets. Width: 50mm Height: 25mm Lenght: 100mm Lamellar Blocks allow you to create an optimal clamping surface for workpieces that can not be clamped to the classical surface of a magnetic clamping plate . It also serves to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the workpiece. Another benefit is the possibility of additional machining (machining) of this block for differently shaped workpieces. Ref. No. 2015-401

Lamellar prism magnetic block Poles pitch: 2,5 3mm Suitable for permanent magnets and electromagnets. Width: 58mm Height: 45mm Lenght: 51mm Laminar Prismatic Blocks allow you to create an optimal clamping surface for workpieces that can not be clamped to their classical surface by a magnetic clamp plates. It also serves to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the workpiece. Another benefit is the possibility of additional machining (machining) of this block for differently shaped workpieces. Ref. No. 2015-402

Lamellar prism magnetic block Poles pitch: 2,5 3mm Suitable for permanent magnets and electromagnets. Width: 60mm Height: 48mm Length: 110mm Laminar Prismatic Blocks allow you to create an optimal clamping surface for workpieces that can not be clamped on to the classical surface of a magnetic clamp plates. It also serves to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the workpiece. Another benefit is the possibility of additional machining (machining) of this block for differently shaped workpieces. Ref. No. 2015-403

Set contains 8 pcs of lamellar magnetic blocks of the following dimensions: 2x flat 46x60x15, pole pitch 2 2,5mm 4x flat 50x100x25, pole pitch 2,5 3mm 2x with double V-groove 9 and 18mm , 57x49x46, pole pitch 3,5 3,5mm Suitable for permanent magnets and electromagnets. Laminar prismatic blocks allow you to create an optimal clamping surface for workpieces that can not be clamped onto the classical surface of a magnetic clamping plate for their shape. It also serves to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the workpiece. Another benefit is the possibility of additional machining (machining) of this block for differently shaped workpieces. Obj. No. 2015-410

Hand Picker Permanent Magnet Dimensions: 112x178 mm Ref. No. 2015-440

Hand collector clips Equipped with a permanent magnet To grasp the scrap metal, just pull the handle Impact resistant design When lifting objects with a diameter> 105mm lifts 4.4kg . When lifting smaller diameters