Turning

Turning knife, right, with soldered blade Square: according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223712 / CSN 22 3712, DIN4972, DIN4972R, ISO2 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Fixed lathe tip with 60 ° apex angle and sintered carbide insert Morse taper size: according to the selected variant Other dimensions - see labels for individual variants The whole tip is hardened to a hardness of HRC 58 to 62. Standard: ČSN 243311 / ČSN 24 3311 / DIN806 / DIN 806 Fixed tips are Czech-made, unused, come from excess stock. Only a limited selection.

Swivel chuck is designed for work on lathes. Morse taper: according to the selected variant Other dimensions and parameters - see the enclosed catalog sheet Standard: ČSN 24 3328 Their extended clamping part allows easy access of the tool to the workpiece, which is especially advantageous when machining tools with exchangeable inserts and when working on copying lathes. The design of the tips allows the radial clearance to be adjusted. The tips have a MORSE ČSN 22 0420 clamping shank (DIN 228, ISO 296) without a clamping thread. Swivel tips are supplied lubricated with lithium grease LV 2-3. It is recommended to relubricate tips used in extreme conditions at intervals of 300 operating hours in quantities up to 1 g through the hole in the housing head (blinded by screw S1) and up to 0.5 g through the hole at the end of the taper shank (blinded by screw S2). Disassembly of the rotating tips is not recommended.

Quick-change knife holder for multi-fix Size: according to the chosen variant Suitable for head / multifix: according to the selected variant Other dimensions - see attached catalog sheet

Turning knife left with soldered blade Square: according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223713 / CSN 22 3713, DIN4972, DIN4972L, ISO2 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Turning knife left with soldered blade Square: according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223713 / CSN 22 3713, DIN4972, DIN4972L, ISO2 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Fixed lathe tip with 60 ° apex angle and sintered carbide insert Morse taper size: according to the selected variant Other dimensions - see labels for individual variants The whole tip is hardened to a hardness of HRC 58 to 62. Standard: ČSN 243311 / ČSN 24 3311 / DIN806 / DIN 806

Quick-change round knife holder for multi-fix Size: according to the chosen variant Suitable for head / multifix: according to the selected variant Other dimensions - see attached catalog sheet

Quick-change parting knife holder for multi-fix Size: according to the chosen variant Suitable for head / multifix: according to the selected variant Other dimensions - see attached catalog sheet

Morse swivel tip for clamping heavy workpieces Morse taper: according to the selected variant Other dimensions and parameters - see description for individual variants Top angle: 60 ° Standard: ČSN 24 3325 Type N: Throw 0.04mm Type E: Throw 0.01mm

Morse swivel tip for clamping heavy workpieces Morse taper: according to the selected variant Other dimensions and parameters - see description for individual variants Top angle: 90 ° Standard: ČSN 24 3325 Type N: Throw 0.04mm Type E: Throw 0.01mm

Quick-change holder for Morse clamping sleeves for multi-fix Size (diameter x length): according to the selected variant Suitable for head / multifix: according to the selected variant Other dimensions - see attached catalog sheet