Metal drills, cylinder. stalk

Carbide drill for drilling bent taps For tap: M12 d1(H7): 10,20 mm Max. depth l3: 35mm Total length l1: 80mm Clamping shank: cylindrical 12 edges Helix angle: 0A ‚ ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide < b> Procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0070

Carbide drill set for drilling bent taps For taps: M3 - M4 - M5 - M6 - M8 - M10 - M12 d1(H7): 2.5 / 3.3 / 4.2 / 5.0 / 6.8 / 8.5 / 10.2 mm Max. depth l3: 10/14/19/23/23/25/35 mm Total length l1: 38/46/50/50/60/80/80 mm Clamping shank: cylindrical Hexagon < br> Helix angle: 0  ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1865

Extended black right-handed steel twist drill with cylindrical shank Diameter: 10.2mm Drill length: Extended width Series - lengths see attached photo( same length as for DIN340 drills) Drilling depth: 10xD cutting angle: 118 ° C > Helix angle: 25 ° to 30 ° Material: HSS - High speed steel Standard: ÄOSN 221125, black extension drills Usage: General - hand, stand, column drills Non-alloy steel, cast steel with strength up to 600 N / mm2

Set of 5 pcs - 3-edged right-cut ground spiral cobalt drill bits for steel and stainless steel with cylindrical shank Set contains diameters: 4 / 5 / 6 / 8 / 10 mm Drill length: Short series - lengths see attached photo Material: HSSE - High-speed steel Co5 / HSSCo5 Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: Stand and column drills, NC and CNC machines, possibly also hand drills. Structural steel Unalloyed and alloyed steel, cast steel with strength up to 850N/mm2 Stainless steel Wrought aluminum alloys and other aluminum alloys Advantages: Higher geometry / hole ovality - depending on the machine used, accuracy up to IT9 can be achieved. Thanks to three blades, the feed can be increased by up to 60%. The special geometry of the tip of the drill prevents the drill from slipping. Thanks to this, there is no need to use a punch to center the holes. The drill does not jam when re-drilling an existing hole. The chip is removed without a problem, less wear on the drill bit / longer service life, thanks to the distribution of the engagement on 3 blades. Cat. no.: 283054005

The photo is illustrative - new - we will take a photo immediately after stocking. Set of 19 pcs - 3-edged right-cut ground spiral cobalt drill bits for steel and stainless steel with cylindrical shank Set contains diameters: 1.0-10.0mm x 0.5mm Length of the drill: Short series - lengths see attached photo Material: HSSE - High-speed steel Co5 / HSSCo5 Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: Stand and column drills, NC and CNC machines, possibly even hand drills. Structural steel Unalloyed and alloyed steel, cast steel with strength up to 850N/mm2 Stainless steel Wrought aluminum alloys and other aluminum alloys Advantages: Higher geometry / hole ovality - depending on the machine used, accuracy up to IT9 can be achieved. Thanks to three blades, the feed can be increased by up to 60%. The special geometry of the tip of the drill prevents the drill from slipping. Thanks to this, there is no need to use a punch to center the holes. The drill does not jam when re-drilling an existing hole. The chip is removed without a problem, less wear on the drill bit / longer service life, thanks to the distribution of the engagement on 3 blades. Cat. no.: 283057019

The photo is illustrative - new - we will take a photo immediately after stocking. Set of 24 pcs - 3-edged right-cut ground spiral cobalt drill bits for steel and stainless steel with cylindrical shank Set contains diameters: 1.0-10.5mm x 0.5mm drill bits 3.3 / 4.2 / 6.8 / 10.2 mm Drill length: Short series - lengths see attached photo Material: HSSE - High speed steel Co5 / HSSCo5 Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: Stand and column drills, NC and CNC machines, possibly also hand drills. Structural steel Unalloyed and alloyed steel, cast steel with strength up to 850N/mm2 Stainless steel Wrought aluminum alloys and other aluminum alloys Advantages: Higher geometry / hole ovality - depending on the machine used, accuracy up to IT9 can be achieved. Thanks to three blades, the feed can be increased by up to 60%. The special geometry of the tip of the drill prevents the drill from slipping. Thanks to this, there is no need to use a punch to center the holes. The drill does not jam when re-drilling an existing hole. The chip is removed without a problem, less wear on the drill bit / longer service life, thanks to the distribution of the engagement on 3 blades. Cat. no.: 283057024

The photo is illustrative - new - we will take a photo immediately after stocking. Set of 25 pcs - 3-edged right-cut ground spiral cobalt drill bits for steel and stainless steel with cylindrical shank Set contains diameters: 1.0-13.0mm x 0.5mm Length of the drill: Short series - lengths see attached photo Material: HSSE - High-speed steel Co5 / HSSCo5 Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: Stand and column drills, NC and CNC machines, possibly even hand drills. Structural steel Unalloyed and alloyed steel, cast steel with strength up to 850N/mm2 Stainless steel Wrought aluminum alloys and other aluminum alloys Advantages: Higher geometry / hole ovality - depending on the machine used, accuracy up to IT9 can be achieved. Thanks to three blades, the feed can be increased by up to 60%. The special geometry of the tip of the drill prevents the drill from slipping. Thanks to this, there is no need to use a punch to center the holes. The drill does not jam when re-drilling an existing hole. The chip is removed without a problem, less wear on the drill bit / longer service life, thanks to the distribution of the engagement on 3 blades. Cat. no.: 283057025

Set of 5 pcs multi-purpose right-cut ground twist drills / "tooth drills" with cylindrical shank - with graduated tip Set includes drill bits: 4 / 5 / 6 / 8 / 10 mm Drill length: Short series - lengths see attached photo Material: HSS - High-speed steel Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: - universal Steel, cast iron, hard wood, plastic, acrylic glass, non-ferrous metals Advantages: Universal use Easier drilling - no need to pre-drill the hole with a smaller average. Perfect for tapping Cat. no.: 283064005

Set of 24 pcs multi-purpose right-cut ground spiral drills / "tooth drills" with cylindrical shank - with graduated tip The set includes drills: 1.0-10.5mm x 0.5mm drills 3.3 / 4, 2 / 6.8 / 10.2 mm Drill length: Short series - lengths see attached photo Material: HSS - High-speed steel Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: - universal Steel, cast iron, hardwood, plastic, acrylic glass, non-ferrous metals Advantages: Universal use Easier drilling - it is not necessary to pre-drill a hole with a smaller diameter. Perfect for tapping Cat. no.: 283064024

Set of 81 pcs of ground cobalt spiral drills for metal with reinforced core 2.0-10.0 mm Top angle: 128  ° special cut according to DIN 1412, shape C( for heavy-duty machining of stainless steels and special materials) Helix angle: 35-40  ° Material: HSS Co5(5 o5) Standard: DIN338 GT100(replaces PN 2907 T1000) Cobalt tungsten-molybdenum steel with very good cutting properties, hardness at elevated temperatures and toughness, suitable for heavy Highly machinable materials. Plastic order with cover. Application: General - hand, stand, column drills Alloy steel, cast steel with strength over 1000 N / mm2 Stainless steel Steel for volume hot and cold forming, rolling mill rolls, steel for cementing and tempering Compared to the "RTi" profile, these drills have an even stronger core and the helix is ??â € ‹â €‹ denser. High rigidity during drilling, for material forming a brittle chip and material with high strength - tough.

Extra long right-hand twist drill for steel with cylindrical shank Diameter: 7.0mm Drill length / helix length: 290/200mm Blade angle: 118° Helix angle: 25° to 30° Material: HSS High-speed steel Standard: DIN1869, ZV 3001 Usage: Especially long drills recommended for drilling deep holes through drill bits housings in parts made of unalloyed and alloyed steel, cast steel up to a strength of 900 N/mm2, gray, tempered and malleable cast iron, sintered steel, etc. When drilling deep holes, it is necessary to prevent clogging of the grooves by frequently moving the drill out of the drilled hole. In view of the poor supply of cutting fluid, it is necessary to reduce the recommended cutting conditions. Cat. No. : A180702V000S

Set of 10 HSS drills for metal, drills with fitted / reduced cylindrical shank Drills: 14; 15; 15.5; 16; 17; 17.5; 18; 19; 19.5; 20 mm Clamp shank: 13mm Packed in a metal case Standard: DIN338, HSS-GK, type N