Lathe knives and inserts

Right holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Designation of plates that fit into the holder: according to the selected variant (TPMT or TPGX) Angle of the plate to the axis: 93° Other dimensions - see product description for individual variants The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (CCMT or CCGT) Angle of the plate to the axis: 95° Other dimensions - see product description for individual variants The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (DCMT or DCGT) Angle of the plate to the axis: 107.5° Other dimensions - see product description for individual variants The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning, for internal cooling Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (DCMT or DCGT) Angle of the plate to the axis: 107.5° Other dimensions - see product description for individual variants The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (TCMT or TCGT) Angle of the plate to the axis: 90° Other dimensions - see product description for individual variants The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Right side turning knife with soldered blade Square: according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223716 / CSN 22 3716, DIN4980, DIN4980R, ISO6 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Right side turning knife with soldered blade Square: according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223716 / CSN 22 3716, DIN4980, DIN4980R, ISO6 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Left side turning knife with soldered blade Knife size: (clamping height x width): according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223717 / CSN 22 3717, DIN4980, DIN4980L, ISO6 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Left side turning knife with soldered blade Knife size: (clamping height x width): according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223717 / CSN 22 3717, DIN4980, DIN4980L, ISO6 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Turning insert for hardened steel, replaceable insert, insert DCGW 070204 HRC55 Suitable for holders for DCMT / DCGT inserts. Radius: 0,4mm Material: CBN(2x) Coating: uncoated HRC55 Series: Fine-grained 70% CBN granulate with ceramic binder, high rigidity and resistance to shocks. Suitable for roughing hardened steels 45-65 HRC, cast iron and very hard alloys such as Inconel, surface hardened steels, etc. Suitable for intermittent cutting. Application: Cast iron: K05-K15 Carbide and hardened steels: H10-H25(45-65 HRC) Cutting conditions: Hardened steel: Vc = 80-240m / min; fn = 0.12-0.25mm / rev. ; Ap = 0,5-2,5mm Ductile iron: Vc = 60-150m / min; fn = 0.20-0.30mm / rev. ; Ap = 0.6-2.5mm Gray cast iron: Vc = 500-1500m / min; fn = 0.50-0.80mm / rev. ; Ap = 0.25-1.0mm Hard alloys with Co> 17%: Vc = 20-40m / min; fn = 0.20-0.30mm / rev. ; Ap = 0.1-0.5mm Manganese steels: Vc = 140-200m / min; fn = 0.3-0.7mm / rev. ; Ap = 0,2-2,9mm The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 5 pcs in the basket.

Turning insert for hardened steel, replaceable insert, insert DCGW 11T304 HRC55 Suitable for holders for DCMT / DCGT inserts. Radius: 0,4mm Material: CBN(2x) Coating: uncoated HRC55 Series: Fine-grained 70% CBN granulate with ceramic binder, high rigidity and resistance to shocks. Suitable for roughing hardened steels 45-65 HRC, cast iron and very hard alloys such as Inconel, surface hardened steels, etc. Suitable for intermittent cutting. Application: Cast iron: K05-K15 Carbide and hardened steels: H10-H25(45-65 HRC) Cutting conditions: Hardened steel: Vc = 80-240m / min; fn = 0.12-0.25mm / rev. ; Ap = 0,5-2,5mm Ductile iron: Vc = 60-150m / min; fn = 0.20-0.30mm / rev. ; Ap = 0.6-2.5mm Gray cast iron: Vc = 500-1500m / min; fn = 0.50-0.80mm / rev. ; Ap = 0.25-1.0mm Hard alloys with Co> 17%: Vc = 20-40m / min; fn = 0.20-0.30mm / rev. ; Ap = 0.1-0.5mm Manganese steels: Vc = 140-200m / min; fn = 0.3-0.7mm / rev. ; Ap = 0,2-2,9mm The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 5 pcs in the basket.

Turning insert for hardened steel, replaceable insert, insert CCGW 060204 HRC55 Suitable for holders for CCMT / CCGT inserts. Radius: 0,4mm Material: CBN(2x) Coating: uncoated HRC55 Series: Fine-grained 70% CBN granulate with ceramic binder, high rigidity and resistance to shocks. Suitable for roughing hardened steels 45-65 HRC, cast iron and very hard alloys such as Inconel, surface hardened steels, etc. Suitable for intermittent cutting. Application: Cast iron: K05-K15 Carbide and hardened steels: H10-H25(45-65 HRC) Cutting conditions: Hardened steel: Vc = 80-240m / min; fn = 0.12-0.25mm / rev. ; Ap = 0,5-2,5mm Ductile iron: Vc = 60-150m / min; fn = 0.20-0.30mm / rev. ; Ap = 0.6-2.5mm Gray cast iron: Vc = 500-1500m / min; fn = 0.50-0.80mm / rev. ; Ap = 0.25-1.0mm Hard alloys with Co> 17%: Vc = 20-40m / min; fn = 0.20-0.30mm / rev. ; Ap = 0.1-0.5mm Manganese steels: Vc = 140-200m / min; fn = 0.3-0.7mm / rev. ; Ap = 0,2-2,9mm The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 5 pcs in the basket.