Knives with replaceable plate

Screw for holders JS_PDJNR and JS_PDJNL with 15mm size plate (side) Thread: M8 Overall length: 20mm

S25S STUCR16 90 ° S25S Interchangeable Socket Socket S25S -STUCR16 93 ° Slicer Socket Cutter: 25mm Diameter Front Angle: 0 ° Angle of Blade: -7 ° Overall length of knife: 250mm Replacement plates are marked TC .. 16T3 .. (ie TCMT 16T3 .., TCGT 16T3 .. etc.) The key is provided with the key for the change of the slicer.

Washer for JS_SER holders with 16mm size (side) Washer height: 3,2mm Hole: 3,7mm Washer was flat and has a grinded bottom the screw lift (for angle adjustment)

Washer for holders JS_SER with plate with size( side) 22mm Washer height: Hole: The washer is flat and has a ground surface for lifting with a screw(for angle adjustment)

SWACR 2020 K 08, 90 ° Knife size: 20x20 mm Front angle: 0 ° Blade angle: 0 ° Blade height: 20mm Overall length: 125mm Changeable blades have WC .. 0804 .. (ie WCMT 0804 .., WCGT 0804. etc.) The key is provided with the key for changing the slices.

Rotary slicer PTGNL 2525 P 22, 90 ° Rotary knife PTGNL-2525P22, 90 ° Cutter size: 25x25 mm Front angle: -6 ° Angle of inclination blade: -6 ° Plate height: 25mm Overall length of blade: 170mm Interchangeable pads have TNM markings. 2204.- E (ie TNMG 2204 ..- E, TNMA 2204 ..- E, etc.)

Set of Inside Professional Turning Knives with Interchangeable Plate Clamping Diameter: 10mm Set of Knives (Left): 1x S10K SCLCR 06 (95 °) for CCMT 0602 / CCGT 0602 1x S10K SDQCR 07 (107,5 °) for DCMT 0702 / DCGT 0702 1x S10K STFCR 11 (90 °) for TCMT 1102 / TCGT 1102 * total length of knives is 125mm < br> 1ks key Art.No. KN 3441640

S12M SCLCR 06 (95 °) for CCMT 0602 / CCGT 0602 1x S12M SDQCR 07 (107.5 °) for DCMT 0702 / DCGT 0702 1x S12M STFCR 11 (90 °) for TCMT 1102 / TCGT 1102 plates * total length of blades 150mm < br> 1ks key Art.No. KN 3441641

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head, after landing on the knife surfaces, settle the blade in the correct position and axial height of 16 mm. After inserting a knife with a 6mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of ( axial height) 16mm. If you have a lathe for knives with an axial height higher than 12mm, you must add adequate pads under the holder. Length of holder: 77mm Width: 18mm Height: 24mm Photo is illustrative, shows holder for larger knife

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head settle the blade in the correct position and axial height of 12 mm after landing on the knife surfaces. The holder is double-sided - it is therefore possible to clamp knives with a diameter of 6mm and 8mm. In both cases for an axial height of ( edge height) 12mm If you have a lathe for knives with an axial height higher than 12mm, you must add adequate washers under the holder. Holder length: 64mm Width: 12mm Height: 12mm

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head, after landing on the knife surfaces, settle the blade in the correct position and axial height of 16 mm. The holder is double-sided - it is therefore possible to clamp knives with a diameter of 6mm and 8mm. In both cases for an axial height of ( edge height) 16mm If you have a lathe for knives with an axial height higher than 16mm, you must add adequate washers under the holder. Holder length: 76mm Width: 18mm Height: 16mm

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head, after landing on the knife surfaces, settle the blade in the correct position and axial height of 16 mm. After inserting a knife with a 8mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of ( axial height) 16mm. If you have a lathe for knives with an axial height higher than 12mm, you must add adequate pads under the holder. Length of holder: 77mm Width: 18mm Height: 24mm Photo is illustrative, shows holder for larger knife