Inside - into the hole

Right holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter x Diameter of relief of the holder at the plate: according to the selected variant Designation of plates that fit into the holder: according to the selected variant (WBGT 0601..-L) Other dimensions - see the attached catalog sheet The product comes with a key for changing the slice. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (CCMT or CCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (CCMT or CCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left drilled holder for replaceable blades, fastening with a screw Knife for internal turning, for internal cooling Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (CCMT or CCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (DCMT or DCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (DCMT or DCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (DCMT or DCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter x Diameter of relief of the holder at the plate: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (DCMT or DCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (DCMT or DCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (RCMT or RCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (SCMT or SCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Left holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter x Diameter of relief of the holder at the plate: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (TCMT or TCGT) Other dimensions - see the attached catalog sheet The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.