Collet chucks and collets
-
Morse
-
Steep ISO cone
-
HSK
-
Preparation - to the vise
-
ER clamps with cylindrical shank
-
Clamps - Bushings (J&L)
-
Collets
-
Accessories
-
Collet ER clamp on ISO taper, type DIN2080
ISO steep taper collet clamp ISO cone size: according to the selected variant For ER collets: according to the selected variant Length of the clamp (the part that sticks out from the spindle): according to the selected variant Throwability: up to 0.005mm Standard: DIN 2080, DIN 6499 - manual tool change If you are not sure that you have chosen the right clamp / you are not sure about the standard, you can find a comparison of this standard with other standards in the photos. Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture.
from 36,80 € with VAT -
Collet ER clamp on ISO taper , type DIN69871
ISO steep taper collet clamp ISO cone size: according to the selected variant For ER collets: according to the selected variant Length of the clamp (the part that sticks out from the spindle): according to the selected variant Balance: G6.3 / 12,000 rpm. , or according to the selected variant Throwability: up to 0.005mm Standard: DIN69871 - automatic tool change If you are not sure that you have chosen the right clamp / you are not sure about the standard, you can find a comparison of this standard with other standards in the photos. Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture.
from 38,53 € with VAT -
Collet ER clamp on ISO taper, type BT / JIS6339 MAS
ISO steep taper collet clamp ISO cone size: according to the selected variant For ER collets: according to the selected variant Length of the clamp (the part that sticks out from the spindle): according to the selected variant Balance: G6.3 / 12,000 rpm. , or according to the selected variant Throwability: up to 0.005mm Standard: JIS B 6339 (MAS BT) - automatic tool change If you are not sure that you have chosen the right clamp / you are not sure about the standard, you can find a comparison of this standard with other standards in the photos. Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture.
from 36,15 € with VAT -
Collet ER clamp with morse taper for Czech spindles, securing with a drift nut
Morse taper collet clamp - for Czech spindles Morse cone: according to the selected variant For ER type collets: according to the selected variant Performance of the ER matrix: according to the selected variant Other dimensions - see product description for individual variants Usage : The collet clamp has an overseas cone driving nut that fits the spindles of Czech machines. I.e. these clamps are suitable for Czech spindles that carry tools through this nut + thread. These clamps are suitable for all types - Czech, Chinese and other - spindles with a morse taper. Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture.
from 31,50 € with VAT -
Collet ER clamp with morse taper
Morse taper collet clamp Morse cone: according to the selected variant For ER type collets: according to the selected variant Performance of the ER matrix: according to the selected variant Other dimensions - see product description for individual variants Usage : Suitable for all new spindles where the tools are driven only by the internal thread. This type is not suitable for older Czech spindles, which have a so-called "house" - through which the tools (except the thread) drift. Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture. Standard: DIN228A
from 24,13 € with VAT -
Precision ER11 collet , DIN6499B / 4008E
Clamping collet series: ER 11 Size: according to the selected variant Other dimensions - see the attached catalog sheet Clamping accuracy: 0.015mm Standard: DIN 6499B / 4008E For clamping a drill, cutter, countersink, etc. Dimension of collet : Diameter: 11mm Length: 18mm Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture. The collet is also suitable for thermdrill drilling.
8,34 € with VAT -
Precision ER16 collet , DIN6499B / 426E
Clamping collet series: ER 16 Size: according to the selected variant Other dimensions - see the attached catalog sheet Clamping accuracy: 0.015mm Standard: DIN 6499B / 426E For clamping a drill, cutter, countersink, etc. Dimension of collet : Diameter: 16mm Length: 28mm Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture. The collet is also suitable for thermdrill drilling.
7,14 € with VAT -
Precision collet ER16, accuracy 0.005mm, DIN6499B+ UP / 426EP
Clamping collet series: ER 16 with higher clamping accuracy Size: according to the selected variant Clamping accuracy: 0.005mm Other dimensions - see the attached catalog sheet Standard: DIN 6499B+ / 426EP For clamping a drill, cutter, countersink, etc. Dimension of collet : Diameter: 16mm Length: 28mm Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture. The collet is also suitable for thermdrill drilling.
9,37 € with VAT -
Sealed collet ER16 , DIN6499C / 426EA
Precision clamping sealed collet ER 16 for drills / milling cutters with internal cooling Diameter: according to the selected variant Standard: DIN 6499 C / 426EA Usage : For drills with internal cooling Suitable for central cooling of the drill with internal coolant flow. Dimensions of the collet: Diameter: 16mm Length: 28mm Throwability: 0.015mm Max. pressure tested by the manufacturer: 40bar Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture.
15,05 € with VAT -
Precision ER20 collet , DIN6499B / 428E
Clamping collet series: ER 20 Size: according to the selected variant Other dimensions - see the attached catalog sheet Clamping accuracy: 0.015mm up to a diameter of 10mm (including) Clamping accuracy: 0.020mm over a diameter of 10mm Standard: DIN 6499B / 428E For clamping a drill, cutter, countersink, etc. Dimension of collet : Diameter: 20mm Length: 32mm Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture. The collet is also suitable for thermdrill drilling.
7,73 € with VAT -
ER collet holder with cylindrical shank
Collet holder, collet head for NC, cylindrical shank Diameter of the clamping shank: according to the selected variant For ER collets: according to the selected variant Length of the clamping part: according to the selected variant Other dimensions - see product description for individual variants Throwability: up to 0.005mm Balance: G2.5 / 20,000 rpm Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture. Usage : Clamping of drills, cutters and other tools with a cylindrical shank As a tap without length compensation and reversal - for clamping taps
from 29,54 € with VAT -
Sealed collet ER20 , DIN6499C / 428EA
Precision clamping sealed collet ER 20 for drills / milling cutters with internal cooling Diameter: according to the selected variant Standard: DIN 6499 C / 428EA Usage : For drills with internal cooling Suitable for central cooling of the drill with internal coolant flow. Dimensions of the collet: Diameter: 20mm Length: 32mm Throwability: 0.015mm Max. pressure tested by the manufacturer: 40bar Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture.
15,05 € with VAT