Clamping tools
-
Clamps for milling
-
Drill chucks
-
Clamps for classic lathes
-
Clamps for NC lathes
-
Universal chucks and acc.
-
Drill chucks
-
Vices, dividers and tables
-
Reduction sleeves
-
Magnet. clamps, demagnetizers
-
Boring heads
-
Clamping accessories
-
Control drawing pad - pair, VERTEX
Pair of unused prism cubes with 1 notch from Vertex ( V-cube backing without yoke / prismatic cube ) Dimensions (dimensions according to the attached photo): L: according to the selected variant W : according to the selected variant H : according to the selected variant Other dimensions - see the attached table The accuracy of the flatness of the prismatic grooves for a pair: up to 0.05mm (with a max. distance of the cubes 300mm apart) The price is for a pair - i.e. for 2 cubes
from 21,03 € with VAT -
Driving carrier , type VDC
The driving heart is used for turning the workpiece when clamped between the tips For diameters: according to the selected variant Suitable for grinding or turning between points The drifting of the object is done via an eccentric lever. The front is engaged by a spring, the eccentric lever rests against a pin stop on the lathe flange - see attached catalog sheet.
from 20,80 € with VAT -
Workshop vice YORK, type STANDART
High-quality locksmith's vise YORK mm of Czech production with anvil. Width of the jaws: according to the selected variant The jaws are made of high-quality steel hardened to 45 HRC +- 5 HRC. The vise is equipped with a set of basic jaws (hard jaws). Integrated rotary plate +- 35° with positioning screws. Precise cylindrical guidance. Gate with safety terminals. York standard type: fixed to the base plate with nuts, without special surface treatment. Other special types of jaws can be found in the folder "Jaws for YORK vices"
from 58,06 € with VAT -
Machine vice CSN 243135 / CSN 243136
Recommended ✓Machine vise with movable jaw - with grooved jaws ČSN 243135 for rigid and precise clamping of the workpiece Width of the jaws: according to the selected variant Height of the jaws (after the bed): according to the selected variant, or see the product description for the individual variants Other dimensions - see product description for individual variants Perpendicularity - parallelism of functional surfaces: 0.02 / 100 mm Standard: ČSN 243135 (125mm and 160mm), ČSN 243136 (200mm) Material: Body: ductile iron with min. tensile strength 400MPa Jaws: steel 14220.4, hardness 56+2 HRC
from 666,99 € with VAT -
Milling mandrel for milling head with transverse driving groove, CSN 241440, Zbrojovka
Clearance saleMilling mandrel for clamping cylindrical socket cutters Clamping cone: according to the selected variant Diameter of the cylindrical part for the socket cutter: according to the selected variant Distance from the collar to the end of the clamping part: according to the selected variant Other dimensions - see product description for individual variants Method of clamping the cutter: stones and screw Standard: ČSN241440 / DIN2080 - manual tool change If you are not sure that you have chosen the right clamp / you are not sure about the standard, you can find a comparison of this standard with other standards in the photos. Goods from excess stock, unused
from 50,95 € with VAT -
Reduction sleeve ISO/MK, type DIN2080 tang type
Reduction insert, milling reduction with Morse cavity - for clamping tools with a driver - drills, countersinks, etc. Clamping cone: according to the selected variant Internal Morse cone: according to the selected variant Length of the clamp (the part that sticks out from the spindle): according to the selected variant Design: see product name and photo of individual variants Standard: DIN 2080, ČSN 247211.1 - manual tool change If you are not sure that you have chosen the right clamp / you are not sure about the standard, you can find a comparison of this standard with other standards in the photos.
from 20,38 € with VAT -
Permanent magnetic clamp PMS-M for sander, 140N/cm2
Permanent neodymium (PrNd) magnet Sanding plate with fine pole design. Suitable for holding small and thin workpieces Magnet size: according to the selected variant Other dimensions - see product description for individual variants Nominal clamping force 140N/cm2 Flatness: 0.005mm/100mm Pole distance: Brass (P1) 0.5mm, steel (P2) 1.5mm Accessories: Allen key and clamps for holding the magnet Usable for EDM applications, immersion in dielectric liquids. Usage: under the sander If you need a magnet for a milling machine, we recommend magnets from the PMAG series
from 362,73 € with VAT -
Machine vise with rotating base, type VBV, VERTEX
Rotating machine vice with full bed and groove for draining liquid Width of the jaws: according to the selected variant Revolving range: 360° Other dimensions - see attached catalog sheet or product description for individual variants Possible clamping with or without a wheel - both surfaces ground.
from 214,33 € with VAT -
Workshop vice YORK, type LUX
High-quality locksmith's vise YORK mm of Czech production with anvil Width of the jaws: according to the selected variant The jaws are made of high-quality steel hardened to 45 HRC +- 5 HRC. The vise is equipped with a set of basic jaws (hard jaws). Integrated rotating plate +- 35° with positioning handles. Precise cylindrical guidance. Gate with safety terminals. Type York Lux : * Fastening to the base plate with loops *Spindle and handles zinc chromated. Other special types of jaws can be found in related products
from 73,64 € with VAT -
Milling mandrel for milling head with transverse driving groove DIN2080 , MCT
Milling mandrel for clamping cylindrical socket cutters Clamping cone: according to the selected variant Diameter of the cylindrical part for the socket cutter: according to the selected variant Distance from the collar to the end of the clamping part: according to the selected variant Other dimensions - see product description for individual variants Method of clamping the cutter: stones and screw Standard: DIN 2080 / ČSN241440 - manual tool change If you are not sure that you have chosen the right clamp / you are not sure about the standard, you can find a comparison of this standard with other standards in the photos.
from 60,12 € with VAT -
Reduction sleeve ISO/MK, type DIN2080 tang type , MCT
Reduction insert, milling reduction with Morse cavity - for clamping tools with a driver - drills, countersinks, etc. Clamping cone: according to the selected variant Internal Morse cone: according to the selected variant Length of the clamp (the part that sticks out from the spindle): according to the selected variant Design: see product name and photo of individual variants Standard: DIN 2080, ČSN 247211.1 - manual tool change If you are not sure that you have chosen the right clamp / you are not sure about the standard, you can find a comparison of this standard with other standards in the photos.
from 42,31 € with VAT -
Control pad with clamp
V-cube with yoke - 1pc, control drawing prism cube with yoke Prism length: according to the selected variant Cube width: according to the selected variant Dice height: according to the selected variant Clamping range: see product description for individual variants DIN876/1
from 29,48 € with VAT