Inner Bearing Pullers and Accessories

Adapter( collet) for removing bearings behind the inner bore. Expands in the range 54-58mm Length of the leading part of the collet 8mm, enlarged collar / end of the collet 3.2mm, total length 135mm M10 male thread - can be used with a puller without the use of a reducer. If you plan to clamp the adapter to the reverse( slip) hammer from our offer, it is necessary to buy a reduction of(mufnu) from M10 to M12 - see related products

Puller / puller for inner bearings with adapters This kit is suitable for bearings with an inner diameter of 8 to 58 mm Kit contains: 1x Sliding hammer 1x Puller 1x Set of 10 adapters: 8-11mm, 12-17mm, 18-23mm, 24- 29mm, 30-34mm, 34-38mm, 39-43mm, 44-48mm, 49-53mm, 54-58mm 1x threaded extension M10x1,5 / M10x1,5 1x threaded reduction M10x1,5 / M8x1,25 1x threaded reducer M10x1,5 / M6x1,0 1x spare screw for adapter 1x Case Technical data: Total length of the sliding hammer: 390mm Clamping thread of the drawbar of the hammer: M10 Weight of the hammer( slip no. Part): 850 g Usage: The kit allows you to disassemble the bearings from the bearing after disassembling the shaft. The set is intended for bearings with a hole diameter of 8 â € “58mm Adapters are intended for bearing disassembly, which are inserted into the bearing bore and, after expansion, are firmly held behind its inner ring. The kit contains 10 adapters. A sliding / reversible hammer or a puller is used to develop the pulling force. Instructions for use: - see attached photos and video 1. Select the appropriate collet according to the bearing size 2. Insert the collet into the hole “so that its edges are behind the bearing ring 3. Screw / unscrew the middle mandrel of the collet with two wrenches until the collet is fastened / disassembled in the bearing ring 4. Attach the collet to the slide of the slide hammer or to the puller 5. Move the hammer back sharply so that it strikes the bar adjusting ring. When using the puller, it is enough to gradually tighten - always tighten for a while and wait for

M10 and M12 Threaded Thread Hexagon: 19mm Overall Length: 40mm Hexagon: 19mm Overall Length: S - see related products

Sliding sliding hammer (reversing hammer) for bearing removal Total weight 1,3kg, total length 390mm Clamping thread at end of bar is M12

M10x1,5 and M12x1,75 male threaded reductions Hexagon: 17mm Overall length: 38mm The adapter is suitable for clamping adapters 8-34mm from KN 107710 to puller KN 107710 P - see related products

Internal Bearing Puller (without Adapters), suitable for KN 107710 for Bearing Removal This puller can be used directly with adapters 34-58mm (see photo). For downloading 8-34mm diameter, you need to buy threaded reduction - see "Recommended accessories" or related products Pendulum lenght: 135mm Pads: 10x16mm Rotary nut with hexagon 24mm , in which a M10 male thread is screwed into the M16x1,25 thread. Application: Application: < br> The pivoting arms of the high strength steel puller are finished with support plates. In the middle of the fork, the nut that is passed through the screw is rotatably mounted. On the top side, the screw is ended with a hexagon. There is a thread inside the bolt at the bottom. The clamp that is firmly tightened in the bearing ring rotates the screw together with the puller. Subsequent rotation of the nut occurs while holding the bolt to pull the adapter and pull the bearing out of the bed. Operating Instructions: - See enclosed photos and videos Recommended accessories: 1. Thread reduction M10 - M12 (male thread) to clamp adapters 8-34mm to puller