Pullers

Product count: 56
  • Puller 3 arm 20-165mm x 145mm BUCO

    Puller 3 arm 20-165mm x 145mm BUCO

    Three-arm Puller Hook Pitch 20-165mm Hook Length 145mm Made in Germany (Buco)

    On request
    86,27 € with VAT
  • Pair of spring pullers 300mm

    Pair of spring pullers 300mm

    Puller for springs for passenger cars. Supplied as a pair. Overall length 300mm Maximum opening 260mm. Suitable for spring diameter max. 15mm. Screw diameter: M. Hexagonal Tensioning 24mm

    In stock
    28,27 € with VAT
  • A pair of 360mm spring pullers

    A pair of 360mm spring pullers

    Puller for springs for passenger cars. Supplied as a pair. Overall length 360mm Maximum opening 340mm. Suitable for spring diameter max. 15mm. Screw diameter: M. Hexagonal Tensioning 24mm

    In stock
    16,81 € with VAT
  • Puller 100mm three-arm with jaw locking, Czech production

    Puller 100mm three-arm with jaw locking, Czech production

    Robust high-quality three-arm puller, suitable for disassembly of bearings, pulleys and other rotating circular machine parts Length of arms from pins to packs: 100mm Screw: M14 The puller consists of 3 swinging arms, for which it is possible to change the length 70/78 mm by a simple adjustment. The width of the arms is 8mm. Changing the arm length also changes the maximum opening value. With an arm length of 70mm, the maximum opening between the curved ends of the arms is 100mm, so the diameter of the bearing or pulley can be up to 124mm, but it depends on the height at the clamping point. The maximum possible height of the clamped part is 50 mm. When adjusting the arms to a length of 78 mm, the maximum opening between the curved ends of the arms is 140 mm, the diameter of the bearing or pulley can be up to 124 mm, but it depends on the height at the clamping point. The maximum height of the clamped part is 60 mm. Jaw height (paw): 6mm / 11mm (gap required to lower the bearing) Depth of jaws: 12mm (from shoulder to tooth) Total jaw width: 25mm Tightening and locking the arms in the clamped position is done with a knurled nut on the main screw. By screwing the nut down, the arms are locked in the retracted position. At the place where the thrust screw rests on the tightened part, there is a reinforced steel ball dia. 7.5mm. The size of the thrust bolt is M14x1.5. The cross clamping lever has a diameter of 8 mm and a length of 180 mm. Rigid construction withstands high stress. Especially suitable for lowering bearings, pulleys, gears, etc. When pulling, the jaws are firmly pressed under the part to be scanned.

    In stock
    49,65 € with VAT
  • Spare jaws with nut for KN-2510 puller for internal bearings, Kovonastroje

    Spare jaws with nut for KN-2510 puller for internal bearings, Kovonastroje

    Spare legs(3pcs) nuts for puller KN-2510. The legs break out / chip in 90% of cases inconsistent deployment, when the legs do not occupy the entire circumference of the pawls or when there is not enough space to remove. The contraction is then uneven and some paw breaks because it is not evenly engaged. It is necessary to follow the instructions, to stretch both the puller packs at the same time, and to tighten the hexagon with a wrench. Before removing, we recommend lightly spraying the bearing and tapping it over the washer with a hammer, which may partially release the tension / bearing clogging.

    In stock
    6,82 € with VAT
  • Arm for adjustable two-arm bearing puller

    Arm for adjustable two-arm bearing puller

    Forged arm suitable for VT_ST080x100, VT_ST100x120 and P19783 Thickness of pack: 4mm Shoulder width: 26,5mm Shoulder length: 60mm (without clamping part) Overall length : 90mm

    On request
    8,26 € with VAT
  • MINI puller three-arm 80mm Extol Premium

    MINI puller three-arm 80mm Extol Premium

    Three-armed MINI puller with 80mm packs (adjustable) and black center screw with thread M10 Size 80x80mm (80mm span, 80mm depth) Jaws are one-sided.

    In stock
    14,56 € with VAT
  • Ball joint puller, PROTECO

    Ball joint puller, PROTECO

    Universal Ball Bearing Puller Wingspan 25-60mm For maximum pin diameter 20mm

    In stock
    18,20 € with VAT
  • Ignition rotor puller for motorcycles

    Ignition rotor puller for motorcycles

    Set of rotors, motorcycles (ignition) This set includes motorcycle pullers for most of the world's brands M14x1,5P M16x1,5P M18x1, 5P M19x1P M20x1P M22x1P M22x1,5P M24x1P M25x1,5P M26x1,5P M26x1P M27x1P M27x1,25P < br> M28x1P M28x1,5P

    In stock
    60,98 € with VAT
  • Set of heads for studs - bolts 6 - 12mm

    Set of heads for studs - bolts 6 - 12mm

    > Simply put the spanner on the brush by turning the brush against the rollers that are inside this key and you can loosen or tighten.

    In stock
    18,82 € with VAT
  • Bearing adapter, diameter 8mm

    Bearing adapter, diameter 8mm

    Adapter(collet) for pulling bearings behind the inner hole. For bearings with a bore diameter of 8mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 12mm M12 female thread - can be used with a reversible hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

    On request
    14,33 € with VAT
  • Adapter for bearings, diameter 10mm

    Adapter for bearings, diameter 10mm

    Adapter( collet) for removing bearings behind the inner bore. For bearings with a bore diameter of 10mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 12mm M12 female thread - can be used with a sliding hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

    In stock
    14,33 € with VAT

Pullers