Inner Bearing Pullers and Accessories

Spare legs(3pcs) nuts for puller KN-2510. The legs break out / chip in 90% of cases inconsistent deployment, when the legs do not occupy the entire circumference of the pawls or when there is not enough space to remove. The contraction is then uneven and some paw breaks because it is not evenly engaged. It is necessary to follow the instructions, to stretch both the puller packs at the same time, and to tighten the hexagon with a wrench. Before removing, we recommend lightly spraying the bearing and tapping it over the washer with a hammer, which may partially release the tension / bearing clogging.

Adapter(collet) for pulling bearings behind the inner hole. For bearings with a bore diameter of 8mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 12mm M12 female thread - can be used with a reversible hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

Adapter( collet) for removing bearings behind the inner bore. For bearings with a bore diameter of 10mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 12mm M12 female thread - can be used with a sliding hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

Adapter(collet) for pulling bearings behind the inner hole. For bearings with a bore diameter of 12mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 13mm M12 female thread - can be used with a sliding hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

Adapter(collet) for pulling bearings behind the inner hole. For bearings with a bore diameter of 15mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 30mm M12 female thread - can be used with a sliding hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

Adapter( collet) for removing bearings behind the inner bore. For bearings with a bore diameter of 17mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 32mm M12 female thread - can be used with a sliding hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

Adapter( collet) for removing bearings behind the inner bore. For bearings with a bore diameter of 20mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 30mm M12 female thread - can be used with a sliding hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

Adapter( collet) for removing bearings behind the inner bore. For bearings with a bore diameter of 25mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 30mm M12 female thread - can be used with a sliding hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

Adapter( collet) for removing bearings behind the inner bore. For bearings with a bore diameter of 30mm. Cannot be used for multiple bearing sizes! Max. bearing ring width: 30mm M12 female thread - can be used with a sliding hammer from our offer without the use of a reduction. For use in the puller, it is necessary to purchase a reduction - see related products

Adapter( collet) for removing bearings behind the inner bore. Expands in range 38-43mm Length of guide part of collet 8mm, enlarged collar / end of collet 3.2mm, total length 135mm M10 male thread - can be used with a puller without the use of a reducer. If you plan to clamp the adapter to the reverse( slip) hammer from our offer, it is necessary to buy a reduction of(mufnu) from M10 to M12 - see related products

Adapter( collet) for removing bearings behind the inner bore. Expands in range 43-49mm Length of guide part of collet 8mm, enlarged collar / end of collet 3,2mm, total length 135mm M10 male thread - can be used with a puller without the use of a reducer. If you plan to clamp the adapter to the reverse( slip) hammer from our offer, it is necessary to buy a reduction of(mufnu) from M10 to M12 - see related products

Adapter( collet) for removing bearings behind the inner bore. Expands in range 49-54mm Length of guide part of collet 8mm, enlarged collar / end of collet 3,2mm, total length 135mm M10 male thread - can be used with a puller without the use of a reducer. If you plan to clamp the adapter to the reverse( slip) hammer from our offer, it is necessary to buy a reduction of(mufnu) from M10 to M12 - see related products