Disc cutters

Disc milling cutter, fine-toothed, narrow dia. Diameter of the cutter: according to the selected variant Width of the milling cutter: according to the selected variant Clamping diameter: according to the selected variant Helix angle: 10° Head angle: 12° Material: HSSCo5 (i.e. HSS + Co5) Standard: ZPS 736275 Type H : Intended for milling (finishing) materials of medium to higher strength up to 1200 Mpa. Machining Ra 3.2 and exceptionally 1.6. Order no. code - series: 736275

Fine-tooth narrow disc cutter with straight teeth Diameter of the cutter: according to the selected variant Width of the milling cutter: according to the selected variant Clamping diameter: according to the selected variant Head angle: 12° Material: HSSCo5 (i.e. HSS + Co5) Standard: DIN 1834 B / ZPS 737275 Type N : Universal use. Suitable for materials up to 900 Mpa strength. Order no. code - series: 737275

Fine-tooth narrow disc cutter with straight teeth Diameter of the cutter: according to the selected variant Width of the milling cutter: according to the selected variant Clamping diameter: according to the selected variant Other dimensions - see the attached catalog sheet Brow angle: 8° Material: HSSCo5 (i.e. HSS + Co5) Standard: DIN 885 B / ZPS 739275 Type H : Intended for milling (finishing) materials of medium to higher strength up to 1200 Mpa. Machining Ra 3.2 and exceptionally 1.6. Order no. code - series: 739275

Fine-tooth compound milling cutter, type H Diameter of the cutter: according to the selected variant Width of the milling cutter: according to the selected variant Clamping diameter: according to the selected variant Other dimensions - see product description for individual variants Material: HSS Standard: ČSN 222171

Semi-coarse-toothed disc milling cutter, HSS, right Diameter of the cutter: according to the selected variant Width of the milling cutter: according to the selected variant Clamping diameter: according to the selected variant Other dimensions - see the attached catalog sheet Material: HSS Standard: ČSN 222176

Semi-coarse-toothed disk milling cutter, left Diameter of the cutter: according to the selected variant Width of the milling cutter: according to the selected variant Clamping diameter: according to the selected variant Other dimensions - see product description for individual variants Material: HSS Standard: ČSN 222177

Stepped countersink cutter, straight edge Cutter diameter: 8 x 4.3mm Clamping diameter: 8mm Number of blades: 2 Material: HSSCo5 Standard : custom made Extraordinary stock, unused Suitable for soft materials - plastic, wood, stainless steel The milling cutter is without a cutting edge through the center - a pre-drilled hole is required.

Blade cutter with two grooves for wedging, pr. 80x8 HSS Cutter diameter: 80mm Cutter width: 8mm Number of bits / teeth: 22 Clamping diameter: 22mm Helix angle: 10 ° Front angle: 10 ° Material: HSS Standard: ČSN 222165, corresponds to DIN885 and ISO 2587

Force screw in the knife holder. Thread Size: M2,5 Head: TORX 7 Overall Length of Bolt (Even with Head): 7mm

Safety valve with seal - 10bar / atm Function: At higher pressure in the distribution, the pressure that the spring develops on the ball inside the valve is overcome. This will open, respectively. bounce the ball and release the hole - on the photo. This valve should only serve as a secondary overpressure protection - ie if an electric or mechanical control valve fails.

Couplings for Vices York 100mm Couple - Contains Front and Rear Pin Dimensions (Length / Diameter): 74 / 6mm and 59 / 5mm

Cone Pins for York 125mm Vices Pair - Features Front and Rear Pole Dimensions (Length / Diameter): 90 / 7mm and 76 / 7mm