Accessories

Granite prismatic V-cube / mat - set of 2 pcs Size: according to the selected variant Other dimensions - see product description for individual variants Accuracy : 0 Standard: DIN874, or DIN874/0 Material: the best quality black granite from a granite mine - natural granite Specific density: 2970-3070kg/m3 Strength: 245-254 MPa Elasticity: 120-127 GPa Coefficient of expansion: 4.61 x 10-6 / °C Water absorption: < 0.07% Hardness in Shore: over 70Hs

Granite prismatic cube Size: according to the selected variant Accuracy : 0 Standard: DIN874, or DIN874/0 Material: the best quality black granite from a granite mine - natural granite Specific density: 2970-3070kg/m3 Strength: 245-254 MPa Elasticity: 120-127 GPa Coefficient of expansion: 4.61 x 10-6 / °C Water absorption: < 0.07% Hardness in Shore: over 70Hs

Set (2 pcs) of granite washers, ground on all 4 sides Size: according to the selected variant Accuracy : 0 Flatness: +- 2.6 um Parallelism: +- 13 um Standard: DIN874, or DIN874/0 Material: the best quality black granite from a granite mine - natural granite Specific density: 2970-3070kg/m3 Strength: 245-254 MPa Elasticity: 120-127 GPa Coefficient of expansion: 4.61 x 10-6 / °C Water absorption: < 0.07% Hardness in Shore: over 70Hs

Granite ruler (1pc), ground on all 4 sides, can also be used as a granite board for measuring Size: according to the selected variant * design 630x100x35 is without holes. Accuracy : 00 Flatness: +- 2.0 um Coaxiality: +- 3.0 um Parallelism: +- 10 um Standard: DIN874, or DIN874/00 Material: the best quality black granite from a granite mine - natural granite Specific density: 2970-3070kg/m3 Strength: 245-254 MPa Elasticity: 120-127 GPa Coefficient of expansion: 4.61 x 10-6 / °C Water absorption: < 0.07% Hardness in Shore: over 70Hs

Granite angle Size: according to the selected variant Other dimensions - see the attached catalog sheet Accuracy: 0.002mm Material: the best quality black granite from a granite mine - natural granite Specific density: 2970-3070kg/m3 Strength: 245-254 MPa Elasticity: 120-127 GPa Coefficient of expansion: 4.61 x 10-6 / °C Water absorption: < 0.07% Hardness in Shore: over 70Hs

Granite angle Size: 160x100x20 mm Accuracy: 00 Standard: DIN874, or DIN874 / 0 Material: the highest quality black granite from granite mine - natural granite Specific ensity! Density: 2970-3070kg / m3 Strength: 245-254 MPa Flexibility: 120-127 GPa Coefficient expansion: 4, 61 x 10-6 / A ‚Â ° C Absorbency water:

Granite angle Size: 250x160x25 mm Accuracy: 00 Standard: DIN874, or DIN874 / 0 Material: the highest quality black granite from granite mine - natural granite Specific ensity! Density: 2970-3070kg / m3 Strength: 245-254 MPa Flexibility: 120-127 GPa Coefficient expansion: 4, 61 x 10-6 / A ‚Â ° C Absorbency water:

Granite angle Size: 400x250x40 mm Accuracy: 00 Standard: DIN874, or DIN874 / 0 Material: the highest quality black granite from granite mine - natural granite Specific ensity! Density: 2970-3070kg / m3 Strength: 245-254 MPa Flexibility: 120-127 GPa Coefficient expansion: 4, 61 x 10-6 / A ‚Â ° C Absorbency water:

Insulating pastes are medium-viscosity pastes intended for marking unevenness when fitting the contact surfaces of machine parts(planar and rotating) and molds. . Pastes are good to adhere to any surface, do not smudge and do not dry. It is mainly used in mechanical engineering, in agricultural and repair companies. Pastes are non-toxic, they do not contain any harmful fillers or pigments. Blue or red ink paste is commonly used on common inequalities, but we also recommend trying a combination of blue and yellow ink paste(blue on the guide surfaces and yellow on the ruler) and thus we will achieve an emphasis on resolution for unevenness. At the same time, the effect of glare from the ground surface is removed. Package 35g - plastic box(non-original packaging) Instructions for use: 1. The contact surfaces of the machine parts are cleaned to get rid of mechanical impurities 2. Using rolled felt or felt, apply the paste paste and spread evenly. 3. Inequalities on a flat interface are indicated by a writing ruler. A measure of correct finishing is the achievement of 24 - 31 scratched areas on the surface of 25 x 25 mm(I. accuracy class) 4. At the rotating surfaces, it is applied to the pin, the shaft by which the case is described. 5. You can easily get rid of discolored hands soiled by washing the paste by first washing them with a small amount of oil and then using a handwashing agent - for example. Solvin, or use DW 11 cleaner from Dawex Chemical, which can also be found in our offer.

Insulating pastes are medium-viscosity pastes intended for marking unevenness when fitting the contact surfaces of machine parts(planar and rotating) and molds. . Pastes are good to adhere to any surface, do not smudge and do not dry. It is mainly used in mechanical engineering, in agricultural and repair companies. Pastes are non-toxic, they do not contain any harmful fillers or pigments. Blue or red ink paste is commonly used on common inequalities, but we also recommend trying a combination of blue and yellow ink paste(blue on the guide surfaces and yellow on the ruler) and thus we will achieve an emphasis on resolution for unevenness. At the same time, the effect of glare from the ground surface is removed. Package 80g - plastic box(non-original packaging) Instructions for use: 1. The contact surfaces of the machine parts are cleaned to get rid of mechanical impurities 2. Using rolled felt or felt, apply the paste paste and spread evenly. 3. Inequalities on a flat interface are indicated by a writing ruler. A measure of correct finishing is the achievement of 24 - 31 scratched areas on the surface of 25 x 25 mm(I. accuracy class) 4. At the rotating surfaces, it is applied to the pin, the shaft by which the case is described. 5. You can easily get rid of discolored hands soiled by washing the paste by first washing them with a small amount of oil and then using a handwashing agent - for example. Solvin, or use DW 11 cleaner from Dawex Chemical, which can also be found in our offer.

Insulating pastes are medium-viscosity pastes intended for marking unevenness when matching the contact surfaces of machine parts( planar and rotating) and forem. Pastes are good to adhere to any surface, do not smudge and do not dry. It is mainly used in mechanical engineering, in agricultural and repair companies. Pastes are non-toxic, they do not contain any harmful fillers or pigments. Blue or red ink paste is used on the usual marking of inequalities, but we also recommend trying a combination of blue and yellow ink paste(blue on the guide surfaces and the yellow on the ruler) and thus we will achieve an emphasis on the resolution of inequalities. At the same time, the effect of glare from the ground surface is removed. Package 350g - plastic box Instructions for use: 1. The contact surfaces of the machine parts are cleaned to get rid of mechanical impurities 2. Using rolled felt or felt, apply the paste paste and spread evenly. 3. Inequalities on a flat interface are indicated by a writing ruler. A measure of correct finishing is the achievement of 24 - 31 scratched areas on the surface 25 x 25 mm(I. accuracy class) 4. At the rotating surfaces, it is applied to the pin, the shaft by which the case is described. 5. You can easily get rid of discolored hands soiled by washing the paste by first washing them with a small amount of oil and then using a handwashing agent - for example. Solvin, or use DW 11 cleaner from Dawex Chemical, which can also be found in our offer.

Insulating pastes are medium-viscosity pastes intended for marking unevenness when fitting the contact surfaces of machine parts(planar and rotating) and molds. . Pastes are good to adhere to any surface, do not smudge and do not dry. It is mainly used in mechanical engineering, in agricultural and repair companies. Pastes are non-toxic, they do not contain any harmful fillers or pigments. Blue or red ink paste is commonly used on common inequalities, but we also recommend trying a combination of blue and yellow ink paste(blue on the guide surfaces and yellow on the ruler) and thus we will achieve an emphasis on resolution for unevenness. At the same time, the effect of glare from the ground surface is removed. Package 350g - plastic box Instructions for use: 1. The contact surfaces of the machine parts are cleaned to get rid of mechanical impurities 2. Using rolled felt or felt, apply the paste paste and spread evenly. 3. Inequalities on a flat interface are indicated by a writing ruler. A measure of correct finishing is the achievement of 24 - 31 scratched areas on the surface of 25 x 25 mm(I. accuracy class) 4. At the rotating surfaces, it is applied to the pin, the shaft by which the case is described. 5. You can easily get rid of discolored hands soiled by washing the paste by first washing them with a small amount of oil and then using a handwashing agent - for example. Solvin, or use DW 11 cleaner from Dawex Chemical, which can also be found in our offer.