ZPS - FN Zlín

Carbide drill SK / TK / HA / PVD for aluminum, non-ferrous metals and plastics Diameter: according to the selected variant Helix length: according to the selected variant Total length: according to the selected variant Length: 5D Other dimensions - see the attached catalog sheet Diameters that you only found in the catalog sheet are made to order. Tip angle: 140° Coating: ZrN - Coating with high corrosion resistance and high resistance to adhesion of non-ferrous metals. Machining Al alloys with a lower Si content, or machining of plastics and copper. Standard: DIN6535 HA (smooth shank) Usage : Aluminum, Al-alloys, copper, brass, bronze, plastics and other non-ferrous metals Aluminium, Al-Si alloys (Si < 6%) up to 400 MPa Al-Si alloys (Si < 12%) up to 600 MPa Aluminum alloys ( Si > 12% ) up to 600 MPa Copper, copper alloys, brass and bronze up to 800 MPa Plastics up to 300 MPa Cat. No. - series: S10132 ZrN

Carbide drill SK / TK / HA / PVD Diameter: according to the selected variant Length: 5D Helix angle: 30 - 35° Tip angle: 140° Coating: AlTiN (Aluminum Titanium Nitride) Carbide: fine-grained K20 / K30 Standard: DIN6539 Usage : Steel, stainless steel, titanium, aluminum, nickel, cast iron, plastics, steels up to 65 HRC Low alloy steels up to 600 MPa Alloyed steels up to 1200 MPa Highly alloyed / Tool steels up to 1400 MPa Austenitic / Ferritic stainless steels up to 680 MPa Martensitic stainless steel up to 820 MPa Gray cast iron Catalog number: S10222

NC collet holder HSK A 63 ER 40 - 100 mm Type: HSK A63 ER32 AD - cooling guided through the center Length from cone to holder: 80 mm Max. collet size: 30mm For collets with an outer diameter: 40mm Clamping nut diameter: 63mm Clamping stem design for aut. replacement: DIN69893 A ER32 collets can be purchased additionally. Throwability: up to 0.005mm Balance: G2.5 / 20,000 rpm. Standard: DIN 69893 The collar has a hole for a data carrier according to DIN69873 (Balluffchip)

S25S STUCR16 90 ° S25S Interchangeable Socket Socket S25S -STUCR16 93 ° Slicer Socket Cutter: 25mm Diameter Front Angle: 0 ° Angle of Blade: -7 ° Overall length of knife: 250mm Replacement plates are marked TC .. 16T3 .. (ie TCMT 16T3 .., TCGT 16T3 .. etc.) The key is provided with the key for the change of the slicer.

Self-locking, quick-release, without loop, type SOLID quick-release drill head without handle, up to 16mm Cutting jaws, professional quality. For drilling: 1-16mm Clamping cone: B18 Body diameter: 56mm, total height 100mm MK1, Main Usage: Stand and Column Drills Accuracy: up to 0.12mm

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head, after landing on the knife surfaces, settle the blade in the correct position and axial height of 16 mm. After inserting a knife with a 6mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of ( axial height) 16mm. If you have a lathe for knives with an axial height higher than 12mm, you must add adequate pads under the holder. Length of holder: 77mm Width: 18mm Height: 24mm Photo is illustrative, shows holder for larger knife