Lubricants and cutting oils

Castrol Alusol SL 51 XBB is a water-soluble semi-synthetic metalworking fluid. Weight / volume ratio: 1kg = 1LTR Specially designed for machining of aluminum alloys (**) or low, medium (**) alloy stainless steel (*), non-ferrous metals (*) and cast iron (*). Suitable for Machining - Concentration, Milling, Grinding, Drilling, Thread Cutting Package quantity: 0.5 liter (plastic container with cap) No additives available release formaldehyde and is therefore in compliance with health and safety regulations. Does not contain boron, which means it complies with environmental protection requirements. No level of nitrite and chlorine, which means it meets the requirements of local legislation on waste treatment and environmental protection requirements. Resistant to fungi and bacteria, which extends the life of the liquid and reduces maintenance costs. Resistant against fungal attack, undermines fluid life and reduces downtime and maintenance. Minimum foaming at recommended water hardness. Excellent wetting and cleaning properties enable working fluid to be stored. Good corrosion properties provide a high level of corrosion protection from machines, tools and products. Covering a wide range of machining, which helps reduce costs. Suitable for both soft and hard water 100-1500 ppm CaCO3 Can be diluted by pouring into water while stirring. Dilution ratio is 6-10% (diluted to 8.5l to 12.5l mix) depending on the type of operation and material. Application: Aluminum Alloy ** Low Alloy and Medium Alloy Steel ** High Alloy Stainless Steel * Non-ferrous Metals * Cast Iron Grinding (6-7% concentration) *

Castrol Alusol SL 51 XBB is a water-soluble semi-synthetic metalworking fluid. Weight / volume ratio: 1kg = 1LTR Specially designed for machining of aluminum alloys (**) or low, medium (**) alloy stainless steel (*), non-ferrous metals (*) and cast iron (*). Milling, Grinding, Drilling, Thread Cutting Contains formaldehyde-free additives , and is therefore in compliance with health and safety regulations. Does not contain boron, which means it complies with environmental protection requirements. No level of nitrite and chlorine, which means it meets the requirements of local legislation on waste treatment and environmental protection requirements. Resistant to fungi and bacteria, which extends the life of the liquid and reduces maintenance costs. Resistant against fungal attack, undermines fluid life and reduces downtime and maintenance. Minimum foaming at recommended water hardness. Excellent wetting and cleaning properties enable working fluid to be stored. Good corrosion properties provide a high level of corrosion protection from machines, tools and products. Covering a wide range of machining, which helps reduce costs. Suitable for both soft and hard water 100-1500 ppm CaCO3 Can be diluted by pouring into water while stirring. The dilution ratio is 6-10% (diluted to 16.7l to 25l mix) depending on the type of operation and material. Application: Aluminum Alloy ** Low Alloy and Medium Alloy Steel ** High Alloy Stainless Steel * Non-ferrous Metals * Cast Iron Grinding (6-7% concentration) * Milling, turning (6-8% concentration) ** Drilling (7-9% concentration) **

Castrol Alusol SL 51 XBB is a water-soluble semi-synthetic metalworking fluid. Weight / volume ratio: 1kg = 1LTR Specially designed for machining of aluminum alloys (**) or low, medium (**) alloy stainless steel (*), non-ferrous metals (*) and cast iron (*). Home Suitable for machining - soutružení, milling, grinding, drilling, tapping Units: 5 liters (plastic container with cap) does not contain ingredients that release formaldehyde , and is therefore in compliance with health and safety regulations. Does not contain boron, which means it complies with environmental protection requirements. No level of nitrite and chlorine, which means it meets the requirements of local legislation on waste treatment and environmental protection requirements. Resistant to fungi and bacteria, which extends the life of the liquid and reduces maintenance costs. Resistant against fungal attack, undermines fluid life and reduces downtime and maintenance. Minimum foaming at recommended water hardness. Excellent wetting and cleaning properties enable working fluid to be stored. Good corrosion properties provide a high level of corrosion protection from machines, tools and products. Covering a wide range of machining, which helps reduce costs. Suitable for both soft and hard water 100-1500 ppm CaCO3 Can be diluted by pouring into water while stirring. Dilution ratio is 6-10% (diluted to 83.5l to 100l of mixture) depending on the type of operation and material. Application: Aluminum Alloy ** Low Alloy and Medium Alloy Steel ** High Alloy Stainless Steel * Non-ferrous Metals * Cast Iron Grinding (6-7% concentration) * Milling

Castrol Alusol SL 51 XBB is a water-soluble semi-synthetic metalworking fluid. Weight / volume ratio: 1kg = 1LTR Specially designed for machining of aluminum alloys (**) or low, medium (**) alloy stainless steel (*), non-ferrous metals (*) and cast iron (*). Milling, Grinding, Drilling, Thread Cutting - , and is therefore in compliance with health and safety regulations. Does not contain boron, which means it complies with environmental protection requirements. No level of nitrite and chlorine, which means it meets the requirements of local legislation on waste treatment and environmental protection requirements. Resistant to fungi and bacteria, which extends the life of the liquid and reduces maintenance costs. Resistant against fungal attack, undermines fluid life and reduces downtime and maintenance. Minimum foaming at recommended water hardness. Excellent wetting and cleaning properties enable working fluid to be stored. Good corrosion properties provide a high level of corrosion protection from machines, tools and products. Covering a wide range of machining, which helps reduce costs. Suitable for both soft and hard water 100-1500 ppm CaCO3 Can be diluted by pouring into water while stirring. The dilution ratio is 6-10% (diluted to 167l to 200l of mixture) depending on the type of operation and material. Application: Aluminum Alloy ** Low Alloy and Medium Alloy Steel ** High Alloy Stainless Steel * Non-ferrous Metals * Cast Iron Grinding (6-7% concentration) * Milling, turning (6-8% concentration) ** Drilling (7-9% concentration) ** Reaming (8-10% concentration

Brunox Turbo-Spray power 500 ml is an essential aid in long-term maintenance, where it lubricates, cleans, loosens screws and prevents corrosion. The lubricant also absorbs water. 5in1: * Lubricant * Corrosion protection * Contact spray * Solvent solvents * Service spray Doesn't dry out like other commercially available WD lubricants. Contains higher and higher quality content of the lubricating component. Highly flammable.

Brunox Turbo-Spray power 500 ml is an essential aid in long-term maintenance, where it lubricates, cleans, loosens screws and prevents corrosion. The lubricant also absorbs water. 5in1: * Lubricant * Corrosion protection * Contact spray * Solvent solvents * Service spray Doesn't dry out like other commercially available WD lubricants. Contains higher and higher quality content of the lubricating component. Highly flammable. Including an extension that is non-removable. In the vertical position of the attachment, it is possible to use the spray in the usual way - for a short time. See photo.

Brunox Turbo-Spray power 100 ml is an essential aid in long-term maintenance, where it lubricates, cleans, loosens screws and prevents corrosion. The lubricant also absorbs water. 5in1: * Lubricant * Corrosion protection * Contact spray * Solvent solvents * Service spray Doesn't dry out like other commercially available WD lubricants. Contains higher and higher quality content of the lubricating component. Highly flammable.

Protective agent for stabilization - corrosion protection with extra long-term effect. Strongly holding, hardening. It dries after 1-2 hours, hardens after 12 hours. Heat resistance up to 80A ‚Â ° C Repels moisture and salt water Use and action: * As protection against corrosion during storage outdoors or sea transport. * For shafts, motors, steel coils, valves, machines, precision tools, semi-finished and finished products, agricultural and construction vehicles, equipment eho kind. * Suitable where chrome plating, galvanizing, etc. are not possible. It is applied on a clean dry surface, if the surface is a bit damp, we recommend use Brunox Turbo Spray beforehand - spray it into all cavities and corners so that the moisture disappears. Any water will drop into drops, then wipe the set with a cloth and apply IX 100. The applied layer should be at least 20um thick. The ideal is a dry layer of 50um, which you will achieve when applying 125um of IX100(even at a consumption of 0.63l / m2). Disposal of preparation IX 100: With varnish or cleaning gasoline or with the help of a high-pressure cleaner and a solution from surfactants.

Lubricating grease for manual mini grease press Volume: 2x 100g Cartridge thread: dia. 13.8mm x 19 strokes per inch (regular thread of plastic 100g cartridges) Lubricant temperature range: 10°C - 120°C Drop point: 180°C

High-temperature universal lubricant with very good lubricity, mechanical and temperature stability and corrosion protection. ALPHA 2000-HD is a unique grease designed for lubrication in industry, using a completely new approach to thickening technology. It provides exceptional lubricating properties, temperature stability, corrosion protection and resistance to water leaching. Its mechanical stability surpasses conventional Vaseline and is why it is ideal in extremely high load applications. It does not contain heavy metals or other components endangering the environment. It has no significant weaknesses and is probably the closest to the idea of ??a universal lubricant on the market today. ALPHA 2000-HD can be recommended for any application where good lubricity, mechanical and temperature stability and corrosion protection are required. Operations using lithium, calcium, aluminum complex or polyurea base can be easily converted to ALPHA 2000-HD to improve performance, reduce costs and reduce maintenance time. - Bearings subjected to leaching water(paper industry etc. 29 29 - Can also be used as an anti-corrosion layer under vices and other clamping mechanisms in CNC machines Thickened: calcium sulfonate complex Water resistant. The lubricant is very suitable for application "under the vice, horses" on machine tools. NLGI grade: 2 Maximum working temperature: 205° C Freezing point: -15° C Dropping point ASTM D2265: 315° C Oil separation ASTM D1742 -24h at 25° C: 0.17 Rolling stability ASTM D1831, penetration change: 5% 4-ball abrasion test ASTMD2266 40kg 1200rpm at 75° C, 1-hour scar in mm: 0.394 4-ball EP test, ASTM D2596 load abrasion index: 65kg Welding point:> 600kg Timkem OK load, ASTM D2509: 65 lbs

High-temperature universal lubricant with very good lubricity, mechanical and temperature stability and corrosion protection. ALPHA 2000-HD is a unique grease designed for lubrication in industry, using a completely new approach to thickening technology. It provides exceptional lubricating properties, temperature stability, corrosion protection and resistance to water leaching. Its mechanical stability surpasses conventional Vaseline and is why it is ideal in extremely high load applications. It does not contain heavy metals or other components endangering the environment. It has no significant weaknesses and is probably the closest to the idea of ??a universal lubricant on the market today. ALPHA 2000-HD can be recommended for any application where good lubricity, mechanical and temperature stability and corrosion protection are required. Operations using lithium, calcium, aluminum complex or polyurea base can be easily converted to ALPHA 2000-HD to improve performance, reduce costs and reduce maintenance time. - Bearings subjected to leaching water(paper industry etc. 29 29 - Can also be used as an anti-corrosion layer under vices and other clamping mechanisms in CNC machines Thickened: calcium sulfonate complex Water resistant. The lubricant is very suitable for application "under the vice, horses" on machine tools. NLGI grade: 2 Maximum working temperature: 205° C Freezing point: -15° C Dropping point ASTM D2265: 315° C Oil separation ASTM D1742 -24h at 25° C: 0.17 Rolling stability ASTM D1831, penetration change: 5% 4-ball abrasion test ASTMD2266 40kg 1200rpm at 75° C, 1-hour scar in mm: 0.394 4-ball EP test, ASTM D2596 load abrasion index: 65kg Welding point:> 600kg Timkem OK load, ASTM D2509: 65 lbs

High-temperature universal lubricant with very good lubricity, mechanical and temperature stability and corrosion protection. ALPHA 2000-HD is a unique grease designed for lubrication in industry, using a completely new approach to thickening technology. It provides exceptional lubricating properties, temperature stability, corrosion protection and resistance to water leaching. Its mechanical stability surpasses conventional Vaseline and is why it is ideal in extremely high load applications. It does not contain heavy metals or other components endangering the environment. It has no significant weaknesses and is probably the closest to the idea of ??a universal lubricant on the market today. ALPHA 2000-HD can be recommended for any application where good lubricity, mechanical and temperature stability and corrosion protection are required. Operations using lithium, calcium, aluminum complex or polyurea base can be easily converted to ALPHA 2000-HD to improve performance, reduce costs and reduce maintenance time. - Bearings subjected to leaching water(paper industry etc. 29 29 - Can also be used as an anti-corrosion layer under vices and other clamping mechanisms in CNC machines Thickened: calcium sulfonate complex Water resistant. The lubricant is very suitable for application "under the vice, horses" on machine tools. NLGI grade: 2 Maximum working temperature: 205° C Freezing point: -15° C Dropping point ASTM D2265: 315° C Oil separation ASTM D1742 -24h at 25° C: 0.17 Rolling stability ASTM D1831, penetration change: 5% 4-ball abrasion test ASTMD2266 40kg 1200rpm at 75° C, 1-hour scar in mm: 0.394 4-ball EP test, ASTM D2596 load abrasion index: 65kg Welding point:> 600kg Timkem OK load, ASTM D2509: 65 lbs