Cooling and lubrication

DW11 is a grease and grease trap remover a clear grease, grease and oil remover for industrial use. Very strong and fast drying product. It can be used safely on both stainless metal, galvanized, enamelled or aluminum surfaces. Apart from laziness, it has no dangerous properties. Applications: 1. Apply the product on a clean cloth(preferably cotton) and re-apply it at the application site. If necessary, repeat the procedure several times until surface perfectly cleaned. 2. Shiny marks must not remain on the surface after application. Packaging: 1 liter in plastic container(non-original packaging)

DW11 is a grease and grease trap remover a clear grease, grease and oil remover for industrial use. Very strong and fast drying product. It can be used safely on both stainless metal, galvanized, enamelled or aluminum surfaces. Apart from laziness, it has no dangerous properties. Applications: 1. Apply the product on a clean cloth(preferably cotton) and re-apply it at the application site. If necessary, repeat the procedure several times until surface perfectly cleaned. 2. Shiny marks must not remain on the surface after application. Packaging: 5 liters in plastic container(original packaging)

Universal soluble oil for metalworking - replacement for Paramo ERO-SB ERO 1070 Volume: 1 liter Dilution: 4 - 15% Colour: pure light brown Description : Universal water-dilutable cutting and cooling fluid, contains mineral oil with a low content of aromatic hydrocarbons, with anionic and nonionic emulsifiers and corrosion inhibitors, inhibitors for yellow metals and stabilizing agents. Usage: Universal machining fluid for all types of chip machining intended for use in a working concentration of 4-15%. Suitable for machining cast iron, aluminum and yellow metals. When mixed with water with a hardness of up to 60°dH, E13 creates a stable emulsion with excellent viscosity and excellent cooling detergent capacity. Technical and safety data sheet - see attachment. Recommended dilution : Light machining and grinding : 4-7% Medium difficult machining : 7-10% Difficult machining : 10-15% Slow pouring of the concentrate into the water with continuous mixing. Can be used in automatic mixers based on venturi tube. Storage : stable when stored at 10-25°C for 12 months, avoid freezing if possible.

Universal soluble oil for metalworking - replacement for Paramo ERO-SB ERO 1070 Volume: 5 liters Dilution: 4 - 15% Colour: pure light brown Description : Universal water-dilutable cutting and cooling fluid, contains mineral oil with a low content of aromatic hydrocarbons, with anionic and nonionic emulsifiers and corrosion inhibitors, inhibitors for yellow metals and stabilizing agents. Usage: Universal machining fluid for all types of chip machining intended for use in a working concentration of 4-15%. Suitable for machining cast iron, aluminum and yellow metals. When mixed with water with a hardness of up to 60°dH, E13 creates a stable emulsion with excellent viscosity and excellent cooling detergent capacity. Technical and safety data sheet - see attachment. Recommended dilution : Light machining and grinding : 4-7% Medium difficult machining : 7-10% Difficult machining : 10-15% Slow pouring of the concentrate into the water with continuous mixing. Can be used in automatic mixers based on venturi tube. Storage : stable when stored at 10-25°C for 12 months, avoid freezing if possible.

Universal soluble oil for metalworking - replacement for Paramo ERO-SB ERO 1070 Volume: 10 liters Dilution: 4 - 15% Colour: pure light brown Description : Universal water-dilutable cutting and cooling fluid, contains mineral oil with a low content of aromatic hydrocarbons, with anionic and nonionic emulsifiers and corrosion inhibitors, inhibitors for yellow metals and stabilizing agents. Usage: Universal machining fluid for all types of chip machining intended for use in a working concentration of 4-15%. Suitable for machining cast iron, aluminum and yellow metals. When mixed with water with a hardness of up to 60°dH, E13 creates a stable emulsion with excellent viscosity and excellent cooling detergent capacity. Technical and safety data sheet - see attachment. Recommended dilution : Light machining and grinding : 4-7% Medium difficult machining : 7-10% Difficult machining : 10-15% Slow pouring of the concentrate into the water with continuous mixing. Can be used in automatic mixers based on venturi tube. Storage : stable when stored at 10-25°C for 12 months, avoid freezing if possible.

Type: HM 46 - hydraulics in normal conditions (year-round operation) Volume: 1 liter - poured from a barrel Packaging: In a plastic container with a lid Replacement for Paramo Mogul HM-46 General characteristics: Hydraulic oils are intended for use in highly loaded hydraulic systems of industrial machines and equipment, in construction, transport, agriculture, etc. Usage: Hydraulic oils are intended for power transmission in hydrostatic systems and for driving hydraulic devices, i.e. in hydraulic transmissions, control and regulation mechanisms and in other devices that work in severe working conditions (pressure up to 25 MPa in gear pumps and up to 35 MPa in piston pumps, increased ambient temperature and humidity. Standards, specifications: DIN51 524 part 2 - HLP, ISO 11 158 HM For other parameters, see the attached technical and safety sheet.

Type: HM 46 - hydraulics in usual conditions (year-round operation) Volume: 5 liters - poured from a barrel Packaging: In a plastic canister with a lid Replacement for Paramo Mogul HM-46 General characteristics: Hydraulic oils are intended for use in highly loaded hydraulic systems of industrial machines and equipment, in construction, transport, agriculture, etc. Usage: Hydraulic oils are intended for power transmission in hydrostatic systems and for driving hydraulic devices, i.e. in hydraulic transmissions, control and regulation mechanisms and in other devices that work in severe working conditions (pressure up to 25 MPa in gear pumps and up to 35 MPa in piston pumps, increased ambient temperature and humidity. Standards, specifications: DIN51 524 part 2 - HLP, ISO 11 158 HM For other parameters, see the attached technical and safety sheet.

Type: HM 46 - hydraulics in usual conditions (year-round operation) Volume: 10 liters - poured from a barrel Packaging: In a plastic canister with a lid Replacement for Paramo Mogul HM-46 General characteristics: Hydraulic oils are intended for use in highly loaded hydraulic systems of industrial machines and equipment, in construction, transport, agriculture, etc. Usage: Hydraulic oils are intended for power transmission in hydrostatic systems and for driving hydraulic devices, i.e. in hydraulic transmissions, control and regulation mechanisms and in other devices that work in severe working conditions (pressure up to 25 MPa in gear pumps and up to 35 MPa in piston pumps, increased ambient temperature and humidity. Standards, specifications: DIN51 524 part 2 - HLP, ISO 11 158 HM For other parameters, see the attached technical and safety sheet.

Manual mini-lubricator / dosing gun on grease / exchange cartridges Cartridges: 100g Cartridge thread: pr. 13.8mm x 19pcs / inch (standard thread of 100g plastic cartridges) Metal Extension Nozzle Length: 100mm Nozzle Diameter: 0.5mm Nozzle Thread: UNF 1/4 "x 28 Overall Gun Length: 205mm Weight of the Press (without Cartridge): 0.1 kg GISON Manufacturer meets ISO 9001/2000 Quality System

Manual Mini Lubrication Press / Grease Gun / Interchangeable Cartridge with Classic Chuck Lubricant 15x38 Cartridge: 100g Cartridge Thread: pr. 13.8mm x 19 strokes per inch (common thread of plastic 100g cartridges) Chuck clutch / extension: pr. 15 x 38mm Clutch Thread / Attachment: NPT 1/8 "x 27 Overall Length: 145mm Weight of the Press (without Cartridge): 0.1kg Manufacturer GISON meets ISO-9001/2000 Quality System Certification

Professional air lubrication press / pneumatic decalcircuit - automatic When using the trigger, the lubricant is continuously extruded Cartridge: 400g (optional) Flexible Hose: 300mm Metal Extension Length: 170mm Type of Extension Nut: NPT 1/8 "x 27 Overall Length of Press: 180mm Max Pressure: 4.0 - 6.2 Bar (60-90PSI) Air consumption: 0.5 / stroke Inlet fitting: 1/4 " Min. diameter of air hose: 6,5mm Weight of press itself: 1,55 kg Each press has its CE number. breakdown of individual components. The package contains the Declaration of Conformity - according to Directive 2006/42 / EC and EN 792-9. Manufacturer GISON meets ISO-9001/2000 quality system certification

Professional air grease press / pneumatic decalamite - automatic When the trigger is held, lubricant is continuously extruded For cartridges: 400g ( or for direct filling) Length of the metal extension: 170mm Flexible pressure hose is not part of the package - can be purchased additionally - see related products Type of thread on the extensions: NPT 1/8" x 27 Total length of the press: 180mm Max. pressure : 2.75 - 6.8 bar (40-100PSI) Air consumption : 0.5 / stroke Inlet fitting : 1/4" Min. air hose diameter: 6.5mm Weight of the press itself: 1.55 kg Each press has its serial number and CE certification. A drawing with breakdown of individual components. The packaging contains a declaration of conformity - according to directive 2006/42/EC and standard EN 792-9. GISON manufacturer complies with ISO-9001/2000 quality system certification