Insert for M5 tap with torque coupling, TC-820-M5-DIN371, 820-01D

Clamping range: M6 - M24 Clamping shank: BT ISO40 sharp cone Length from spindle: 80mm < br> Standard: JIS 6339 MAS ??BT 40 the attachments are secured behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo (photo is for DIN69871) Extension extension - see photo (photo is for DIN69871) Extensions and taps are not part of the set! Function: The tap is clamped into a suitable TC820 collet which has a pre-set torque clutch or possibly fine-tune it as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Clamping range: M6 - M24 Clamping shank: DIN ISO40 steep taper Length from spindle: 80mm < Tape clamping method: The taps are secured by a square and a shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo Extension extension - see photo Extensions and taps are not a part of the set! Function: The tap is clamped into a suitable TC820 collet, which has a torque clutch already preset, or it can be fine-tuned as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Quick-acting tapping head with length compensation for TC 820 for machine taps according to DIN371 DIN374 and DIN376 Torque coupling is set directly on the collet. Clamping range: M6 - M24 (need to buy TC820 collet) Clamping shank: Morse 3 / MK3 with carrier Tape clamping method: Taps are clamped into the TC820 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC820 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC820 collet, which has a torque clutch already preset, or it can be fine-tuned as needed.

Quick-acting tapping head with length compensation for TC 820 for machine taps according to DIN371 DIN374 and DIN376 Torque coupling is set directly on the collet. Clamping range: M6 - M24 (need to buy TC820 collet) Clamping shank: morse 4 / MK4 with carrier Thread clamping method: Taps are clamped into the TC820 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC820 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC820 collet, which has a torque clutch already preset, or it can be fine-tuned as needed.

Screwdriver head for TC 820 for machine taps according to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque clutch is set directly on the collet. Clamping range: M6 - M24 (need to buy TC820 collet) Clamping shank: morse 4 / MK4 with carrier Thread clamping method: Taps are clamped into the TC820 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC820 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC820 collet, which has a torque clutch already preset, or it can be fine-tuned as needed.

Screwdriver head for TC 820 for machine taps according to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque clutch is set directly on the collet. Clamping range: M6 - M24 (need to buy TC820 collet) Clamping shank: Morse 3 / MK3 with carrier Tape clamping method: Taps are clamped into the TC820 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC820 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC820 collet, which has a torque clutch already preset, or it can be fine-tuned as needed.

Clamping tapping head with length compensation for TC 820 attachments with torque coupling for machine taps Clamping range: M6 - M24 Clamping shank: steep taper DIN ISO50 Length from spindle: 80mm Standard: DIN69871 50 Length compensation - see photo Clamping method vitník: The taps are secured in the attachment by four edges and a clamping shank. The tap is held firmly in the attachment, pulled out after locking the clamping ring at the front of the attachment. Attachments are in the main body over the bearing and stones - see photo Extending the attachment - see photo Attachments and taps are not part of the set! Functions: The tap is clamped in a suitable collet TC820, which has a torque clutch already preset, or it can be fine-tuned as needed. The tap has a length compensation of approx. 0.5 cm, so it is sufficient to program the cutting depth. Torque clutch may prevent the tap from bending.

Quick-action threading head with length compensation for TC 820 attachments with torque coupling for machine taps Clamping range: M6 - M24 Clamping shank: HSK 63A Length from spindle: 105mm Standard: DIN 69893 - HSK-A63 Length compensation - see photo Method of clamping the tap: The taps are secured in the extension by the square and the clamping shank. The tap is firmly held in the extension, pulled out after pressing the clamping collar in the front of the extension. The attachments are secured in the head via the bearing and stones The attachments and taps are not part of the set! Functions: The tap is clamped in a suitable collet TC820, which has a torque coupling already preset, or it can be fine-tuned as needed. The thread cutter has a length compensation of approx. 0.5 cm, so it is enough to program the appropriate cutting depth. The torque coupling prevents the tap from twisting.

norms: DIN69871 Adapters in set of taps: DIN 371 (reinforced stopper): M8; M10; DIN 376 (classical shank): M12; M14; M16; M18; M20 Length compensation - see photo no.3, no.4 and no.12 The set is delivered in the trunk - see photo 9 and no.10 Taper clamping method: The taps are secured in the extension behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo no.5 and no.6 Extension of the extension see photo no.7 and no.8 You can buy the set Taps for M5 - M24 taps - see photo n ° 11 Taps for taps manufactured in accordance with JIS and ISO 529, which are not common in our country, can also be purchased for the die head. Approximately 90% of the domestic market consists of taps made according to DIN standards Taps are not a part of the set!

Home Quick die head with a length compensation for the extension TC 820 for machine taps according DIN371 DIN374 and DIN376 threading Clamping range: M5 - M24 (to buy a separate collet TC820) Home Shank: 20mm cylindrical < Clamping Shank Length: 70mm Tapping Method: Taps are clamped into the TC820 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC820 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC820 collet, which has a torque clutch already preset, or it can be fine-tuned as needed. The screwdriver has a length compensation of approx. 1.0cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Adjustable Key for TC-312 and TC-820 Inserts Range: 7-40 mm Key Diameter Keys: 3,0mm For TC-312 Collet Pins Needed mildly good - inaccuracy from production. For TC-820, use is easy. Ref. : 3404-150