Collet holders

Are you equipping a NC machine or are you just looking for a chuck for your lathe / milling machine? You just found it!

Special offers

  • Slotting groove holder for inserts 8mm, UT-08-25L

    Slotting groove holder for inserts 8mm, UT-08-25L

    Slotting knife / holder for CNC For slot width / insert size: 8mm Face diameter: 20mm Minimum hole diameter: 21.5mm Depth slotting: 100mm Shank diameter: 25mm Shank length: 90mm Other dimensions - see enclosed catalog sheet. The holder is made of heat treated hardened steel. An eccentric sleeve can be purchased with the holder, with which it is very easy to fine-tune the offset of the knife edge, which is ideal when the machine does not have a Y axis for precise adjustment. You can easily eliminate any inaccuracy / error thanks to the possibility of turning the housing (on the scale) by 0.5 mm on both sides. We can also supply these holders in a version for slotting square, hexagonal and spline( multi-groove) profiles - see the enclosed catalog sheet. The holder is delivered without an insert, these are purchased separately - you will find them in related products or in the enclosed catalog sheet. We can offer inserts made of sintered steel HSSE-PM or carbide.

    In stock
    219,07 € with VAT
  • Slotting groove holder for 6 and 8mm inserts, UTSZ-06/08

    Slotting groove holder for 6 and 8mm inserts, UTSZ-06/08

    Slotting knife / holder for slotting machines For slotting width / insert sizes: 6mm and 8mm Knife profile: 15.5 x 12.0mm Minimum hole diameter : 17,9mm / 18,4mm Depth of cut: limited by the total length of the holder / machine Total length of the holder: 220mm Other dimensions - see the enclosed catalog sheet. The holder is made of heat treated hardened steel. The holder is delivered without an insert, these are purchased separately - you will find them in related products or in the enclosed catalog sheet. We can offer inserts made of sintered steel HSSE-PM or carbide.

    In stock
    159,80 € with VAT
  • Grooving insert for slotting holder 8 P9 with chamfer, IN-08-P9-SM

    Grooving insert for slotting holder 8 P9 with chamfer, IN-08-P9-SM

    Slotting grooving insert for UT-holders, with chamfer 0.2mm x45° Insert width: 8mm Edge tolerance: P9(7.985mm) Other dimensions - see enclosed data sheet Material: HSSE-PM( sintered cobalt steel) Coating: TiN Chamfering of the cutting edges helps to prevent the formation of "increments" during slotting / forming at the groove bearing surface. The insert can be re-sharpened 2-3 times. Holders for this insert can be found in related products.

    In stock
    54,47 € with VAT
  • Carbide slotting insert for slotting holder 8 C11, INHM-08-C11

    Carbide slotting insert for slotting holder 8 C11, INHM-08-C11

    Carbide shaping insert for UT- and UTSZ- holders Insert width: 8mm Edge tolerance: C11(8,170mm) Other dimensions - see enclosed catalog sheet Material: TK / SK / VHM - carbide Coating: PVD, TiCN The insert can be reground 2-3 times. Holders for this insert can be found in related products.

    In stock
    56,82 € with VAT
  • Eccentric case for broaching holders with 25mm shank, B-32

    Eccentric case for broaching holders with 25mm shank, B-32

    Eccentric housing with scale for slotting holders with up. shank: 25mm Case outer diameter: 32mm Case length: 85mm More information - see enclosed catalog sheet With this case it is possible to fine-tune the Y-axis for slotting machines holders, thus achieving a precise alignment of the knife edge axis with the workpiece axis. This is ideal when the machine does not have a Y axis for precise adjustment. You can easily eliminate any inaccuracy / error thanks to the possibility of turning the case( on the scale) by 0.5 mm on both sides.

    In stock
    227,41 € with VAT
  • Clamping sleeve 35x35mm for broaching holders 25mm, AD-35

    Clamping sleeve 35x35mm for broaching holders 25mm, AD-35

    Clamping reduction sleeve for slotting machine - for clamping holders type BT(see appendix) for slotting holders with up. shank: 25mm Housing clamping dimension: 35mm x 35mm Housing length: 140mm Holders are clamped in the housing with two M12 screws More information - see enclosed catalog sheet With the help of this sleeve, it is possible to clamp CNC shaping holders type BT in the slotting machine - see the enclosed catalog sheet

    In stock
    208,08 € with VAT

Vacuum clamping

Do you machine aluminum, plastic or other non-magnetic material? Try vacuum!

View products

Magnetic clamping

For conservative workers we also have classic magnets - now extra strong!

View products
  • Clamping sleeve 35x41,5mm prismatic for broaching holders 25mm, ADP-35

    Clamping sleeve 35x41,5mm prismatic for broaching holders 25mm, ADP-35

    Clamping reduction sleeve for slotting machine - for clamping holders type BT(see appendix) for slotting holders with up. shank: 25mm Housing clamping size: 35mm x 41.5mm Housing length: 140mm The holders are clamped in the housing with two M12 screws More information - see the enclosed catalog sheet With the help of this sleeve, it is possible to clamp CNC shaping holders type BT in the slotting machine - see the enclosed catalog sheet

    On request
    184,78 € with VAT
  • Slotting holder for square profile 13-16mm, UT-SQ-13 / 16-25

    Slotting holder for square profile 13-16mm, UT-SQ-13 / 16-25

    Trimming knife / holder for CNC for trimming squares / square profiles / quads / 4hr. For squares of sizes: 13 to 16mm Face diameter: 12mm Minimum hole diameter: 13mm Depth of cut: 50mm Shank diameter: 25mm Clamping shank length: 90mm Other dimensions - see enclosed catalog sheet. The holder is made of heat treated hardened steel. An eccentric sleeve can be purchased with the holder, with which it is very easy to fine-tune the offset of the knife edge, which is ideal when the machine does not have a Y axis for precise adjustment. You can easily eliminate any inaccuracy / error thanks to the possibility of turning the housing (on the scale) by 0.5 mm on both sides. These holders can also be supplied in a design for grooving, hexagonal and spline( multi-groove) profiles - see the enclosed catalog sheet. The holder is delivered without an insert, these are purchased separately - you will find them in related products or in the enclosed catalog sheet. We can offer inserts made of sintered steel HSSE-PM, carbide on request.

    On request
    258,96 € with VAT
  • Slotting holder for hexagonal profile 11-17mm, UT-HEX-11 / 17-25

    Slotting holder for hexagonal profile 11-17mm, UT-HEX-11 / 17-25

    Trimming knife / holder for CNC for trimming hexagons / hexagonal profiles / hexagons, 6hr. For hexagons of size: 11 to 17mm Face diameter: 10mm Minimum hole diameter: 11mm Depth of cut: 40mm Shank diameter: 25mm Clamping shank length: 90mm Other dimensions - see enclosed catalog sheet. The holder is made of heat treated hardened steel. An eccentric sleeve can be purchased with the holder, with which it is very easy to fine-tune the offset of the knife edge, which is ideal when the machine does not have a Y axis for precise adjustment. You can easily eliminate any inaccuracy / error thanks to the possibility of turning the housing (on the scale) by 0.5 mm on both sides. These holders can also be supplied in a version for grooving, square and spline( multi-groove) profiles - see the enclosed catalog sheet. The holder is delivered without an insert, these are purchased separately - you will find them in related products or in the enclosed catalog sheet. We can offer inserts made of sintered steel HSSE-PM, carbide on request.

    On request
    258,96 € with VAT
  • Collet chuck ISO40 x ER32 DIN69871 with a set of 15 collets, L = 70mm

    Collet chuck ISO40 x ER32 DIN69871 with a set of 15 collets, L = 70mm

    Collet chuck ISO 40 x ER 32 - 70 15 pcs of collets ISO40xER32(40xER32) Clamping shank design for cars. exchange: DIN Shaft length with nut: 40mm Set contains wrench and 15 collets Max. collet size: 20mm Standard: DIN 69871 Collet chucks diameters: 2-3mm, 3-4mm, 4-5mm 5-6mm, 6-7mm, 7-8mm, 8 -9mm, 9-10mm, 10 -11mm, 11-12mm, 12-13mm, 13-14mm, 15-16mm, 17-18mm, 19-20mm Throw: up to 0.005mm Balancing: G6.3 / 12,000 rpm. Supplied in a plastic case Pliers clamping procedure: Snap the collet into the clamping nut - according to the Attached image.

    On request
    176,99 € with VAT
  • Machine tap M - HSSE ISO2(6H) with chip breaker, FANAR

    Machine tap M - HSSE ISO2(6H) with chip breaker, FANAR

    Machine tap with straight groove and chip breaker Fitting: ISO2 (6H) Material: HSSE (High speed steel + 5% Cobalt) Coating: uncoated Ground thread profile Standard: DIN 371, DIN374, DIN376 Usage: Structural and carbon steel, low-alloy steel, steel castings up to 800N / mm2 Brass with a long chip Free-cutting steel, structural and case-hardening steel Spherical and malleable cast iron Non-alloy and low-alloy copper alloys Aluminum alloys with Si content

    from 8,76 € with VAT
  • Interchangeable insert CCMT 060204-HMP NC3120, Tornado

    Interchangeable insert CCMT 060204-HMP NC3120, Tornado

    Replacement cutting insert CCMT 060204 - HMP NC3120 Radius: 0,4mm Sheet material: NC3120 - suitable for common machining to roughing of steel. High resistance to chipping, high temperature stability due to Al2O3 coating. Coating: MT-CVD: TiCN Al2O3 TiCN Application: Steel: P20-P25 City type: Medium until the finishing geometry of the breaker for small pieces. The wider wall of the breaker prolongs the life of the insert - even with a sudden change in the depth of the cut. The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

    In stock
    6,30 € with VAT
  • Replaceable insert DCMT 11T304-HMP NC3120, Tornado

    Replaceable insert DCMT 11T304-HMP NC3120, Tornado

    Replacement insert in original packaging, DCMT 11T304 Radius 0,4mm Coating: MT-CVD: TiCN Al2O3 TiCN Series NC3120: < / b> High resistance to chipping, resistant to high temperatures. Application: Steel: P15-P30 HMP Type: Medium to finishing geometry of small chips. The wider wall of the trowel ensures extended plate life - even with sudden change in cutting depth.

    On request
    6,95 € with VAT
  • Replaceable insert WNMG 080404-AL H01, Kovonastroje

    Replaceable insert WNMG 080404-AL H01, Kovonastroje

    Turning insert VBD WNMG 080404 - AL H01 Radius: 0,4mm Coating: uncoated, polished surface Series H01: Suitable for routine and finishing operations - for non-ferrous metals and plastics. Usage: Non-ferrous metals and plastics: N05-N25 Cutting conditions: Vc = 100-200m / min < br> fn = 0.03-0.40 mm / rev. ap = 0,1-5,0 mm Type AL: Very sharp breaker for machining aluminum, plastic. Excellent for machining soft non-ferrous metals and their alloys. The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

    In stock
    6,97 € with VAT

Store at your service

In the store you can choose from our wide range of products or just pick up your order from the eshop. You can pay by card in the store!

Address

Kovonástroje s.r.o.
Masarykova 1107
76302 Zlín - Malenovice

View map

Opening hours

Monday: 8:00 - 17:00
Tuesday: 8:00 - 15:00
Wednesday: 8:00 - 17:00
Thursday: 8:00 - 15:00
Friday: 8:00 - 15:00
( Lunch brake every day 11:00-11:30)

We are not just sellers,
but artisans and DIYers like you!

Our work is our hobby, so in work and at home, we enthusiastically turn, mill, grind, destroy drills, cutters, taps and at the same time we solve new and new situations - just like you! We never get bored under - in any circumstance, we always work through - to the feeling of a job well done :-)

Thanks to that, we will be happy to advise you, and because we keep majority of the most used assortment in stock, we will resolve your order quickly. We will try to make sure that your purchase with us always makes sense and that you are happy to return to us.

More about us

Libor Čejka, company owner

Free shipping

There is possibility of free shipping. For more information click here.

Fast shipping

If on stock, you will recieve your order in 1 working day.

Store

Most of the goods are available at the shop.

Individual discounts

Are you a loyal customer or do you want to become one? Contact us!