Measuring aids

Personal industrial stethoscope / phonendoscope / car sonoscope - sound probe with steel spike Touch probe length: 300mm Locating mechanical damage of motors and other parts Supersonic sound detector used for fast detecting / locating disturbing sounds - noisy bearings, knocking, knocking, etc.

Thread 14x1,25mm - common candle. - Advance Adjustment: 1. Unscrew the spark plug and screw in the timer. 2. Slowly rotate the crankshaft until the piston is in the upper dead center - at this point, the stick of the meter is fully extended. 3. Secure the rod in this position with the side screw - turn the crankshaft about 1/3 turn back (counterclockwise). 4. Set the lead on the advance meter. This is done by screwing the top of the meter. 1 revolution is 1mm, the finer values ??are indicated on the body of the meter. Gently rotate the crankcase in the direction of the engine until the piston reaches the meter bar. 5.Set the breaker (the circuit breaker board) to the position where the contacts are disconnected. 6. The start of the disconnection is determined by the connected bulb, ohmmeter or thin paper. The gauge is suitable for adjusting the range of motorcycles

Thread 14x1,25mm - common candle. Body length without thread: 60mm Included are two bars with a diameter of 5mm and lengths: 50 and 60mm. After assembly of the sticks into the adapter there is a stick overlap of 32mm and 42mm (including thread length) This adapter is fitted with an 8mm stem (8H7 hole)

Thread 14x1,25mm - common candle Length of body without thread: 60mm Included are two bars with a diameter of 5mm and lengths of 50 and 60mm. Indicator: 60mm Indicator step: 0-10mm Splitting: 0.01mm

Measurement advance parameters: Thread 14x1,25mm - common candle. Total height of meter: Indicator - It also goes where there is little room. Joysticks contain 13 sheets in the range of 0.05-1.0mm, length 100mm Adjustment of advance: 1. Unscrew the spark plug and screw in the timer. 2. Slowly rotate the crankshaft until the piston is in the upper dead center - at this point, the stick of the meter is fully extended. 3. Secure the rod in this position with the side screw - turn the crankshaft about 1/3 turn back (counterclockwise). 4. Set the lead on the advance meter. This is done by screwing the top of the meter. 1 revolution is 1mm, the finer values ??are indicated on the body of the meter. Gently rotate the crankcase in the direction of the engine until the piston reaches the meter bar. 5.Set the breaker (the circuit breaker board) to the position where the contacts are disconnected. 6. The start of the disconnection is determined by the connected bulb, ohmmeter or thin paper. The gauge is suitable for adjusting the range of motorcycles

Diesel compression tester - compressiometer for diesel engines - set for testing compression in cylinders Set contains: 1x manometer 0-70bar / 0-1000PSI with drain Flow valve 1x extension 360mm hose for adapters with thread 1x set of adapters for glow plug: M8x1,0 x 102mm, M10x1,0 x 83mm, M10x1,0 x 91mm , M10x1,0 x 113mm, M10x1,0 x 119mm, M10x1,25 x 67mm, M10x1,25 x 135mm, M12x1,25 x 51mm, M22x1,5 x 118mm 1x set of adapters for injectors e: M20x1.5 x 75mm, M22x1.5 x 75mm, M24x1.5 x 88mm, M24x2.0 x 63mm 1x screw adapter 160mm with seal(with thread M18x1.5 ) 1x conical bit for screw adapter 1x puller H piece 1x case Usage: Used to detect a defect in the piston rings, valves, head gaskets, cylinders and drilling cylinders. Screws instead of glow plugs or injectors - via attached adapter, or conical bit with screw adapter H-puller can be used ( must be secured against movement very firmly and securely!).

Petrol compression tester - compressiometer for petrol engines - set of 9 pcs for testing compression in cylinders - Set contains: 1x manometer 0-20kPa(0-20bar) / 0-300PSI with drain valve 1x extension 400mm hose for adapters with thread 5x adapter with thread(M8x1,0, M10x1,0, M12x1,25, M14x1,25, M18x1,5) 1x straight metal bit with rubber tip 1x bare metal bit with rubber tip Usage: Used to detect the problem at Piston rings, valves, head gaskets, cylinders and drilling cylinders. Screws directly to the cylinder - instead of spark plugs through the attached adapter, or directly pressed against the fixed rubber attachment ending.

Personal industrial stethoscope / phonendoscope / car sonoscope - sound probe with steel spike Touch probe length: 300mm Locating mechanical damage of motors and other parts Supersonic sound detector used for fast detecting / locating disturbing sounds - noisy bearings, knocking, knocking, etc.

Vacuum, Pressure Tester, Fuel Underpressure, for Adjustment of Carburetor Valves Pressure Range: 0-7 Atm (0-0,7 kg / cm2) or 0-10 PSI Vacuum Range: 0-70 cm / Hg vac, or 0-28 inch / Hg vac 92mm with 6mm nipple 1 threaded adapter 1 / 8 "NPT - 1/4" NPT 1x 1/8 "NPT - 3/8" NPT Thread Reduction first and second cylinder rolls). Suitable for synchronizing car, motorcycle and other carburettors and injection engines. > Purchase more of these meters for multi-cylinder engines.

Fuel Pump, Carburetor and Carburetor Test Kit with 2-4 Carburetors < 4 pcs of rubber tubes 8x5x7500mm 4 pieces of extension tubes 3,9x52mm and 4 pieces in dimension 3,9x122mm 8 pieces of connectors 8x40mm 4 pcs 10x53mm (M60x0,75) 4 pcs 10x60mm M6x1,0)