Homepage Metalworking tools Turning Lathe knives and inserts

Lathe knives and inserts

Product count: 1775
  • Parting "radeco" holder including HSSCo5 tool bit

    Parting "radeco" holder including HSSCo5 tool bit

    Holder for trapezoidal parting blade ČSN 223693 For radeco with clamping height: according to the selected variant Clamping height of the holder: see product description for individual variants Axial height: see product description for individual variants Set, contains: 1x Partition radeco blade holder according to ČSN 223693 - see product description for individual variants 1x Radeco trapezoidal parting HSSCo5 ČSN 223693 - see product description for individual variants Radeco is secured in the holder with 3 screws Material: hardened steel C50 - Czech production Radeco slices must be made according to the standard: ČSN 223693/22 3693 - see related products

    from 23,78 € with VAT
  • Parting tool bit "radeco" holder CSN 223693 - screw type

    Parting tool bit "radeco" holder CSN 223693 - screw type

    Holder for trapezoidal parting blade ČSN 223693 For radeco with clamping height: according to the selected variant Clamping height of the holder: see product description for individual variants Axial height: see product description for individual variants Radeco is secured in the holder with 3 screws Material: hardened steel C50 - Czech production Radeco slices must be made according to standard: ČSN 223693/22 3693 Price includes holder only, advice must be purchased separately - see related products

    from 9,64 € with VAT
  • Turning knife right-sided straight DIN 4971 R / CSN 223710

    Turning knife right-sided straight DIN 4971 R / CSN 223710
    Clearance sale

    Turning knife straight straight with soldered blade Knife size: (clamping height x width): according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223710 / CSN 22 3710, DIN4971, DIN4971R, ISO1 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

    from 1,86 € with VAT
  • Turning knife right-sided straight DIN 4971 R / CSN 223710 , DENAS

    Turning knife right-sided straight DIN 4971 R / CSN 223710 , DENAS

    Turning knife straight straight with soldered blade Knife size: (clamping height x width): according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223710 / CSN 22 3710, DIN4971, DIN4971R, ISO1 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

    from 4,59 € with VAT
  • Parting tool bit "radeco" holder CSN 223693 - spring type

    Parting tool bit "radeco" holder CSN 223693 - spring type

    Holder for trapezoidal parting blade ČSN 223693 For radeco with clamping height: according to the selected variant Clamping height of the holder: see product description for individual variants Axial height: see product description for individual variants Material: hardened steel - Czech production Radeco slices must be made according to standard: ČSN 223693/22 3693 Price includes holder only, advice must be purchased separately - see related products

    from 12,05 € with VAT
  • Lathe turning insert holder SCLCR

    Lathe turning insert holder SCLCR
    Recommended ✓

    Right holder for inserts / knife for external turning, screw clamping Clamping dimensions: according to the selected variant Designation of the plates that fit into the holder: according to the selected variant Other dimensions - see product description of individual variants. A key for changing the plate is supplied with the goods. The plate is not part of the package, it can be purchased separately. General information on choosing the right holder: Holders type "S" - with screw clamping are suitable for common to finishing operations. They are suitable for smaller material removals. The inserts in these holders have a positive insert back, which enables sharper insert geometries and thus the possibility of achieving a better surface quality. Holders of type "P", "M", "T", "C" and "D" with clamping per inch or clamp are suitable for common to roughing operations - they have higher rigidity. The inserts in these holders have a negative (straight) insert back, thanks to which the inserts do not break out / deform so much and it is possible to roughen them with better and to machine even harder machinable materials.

    from 30,41 € with VAT
  • Lathe turning insert holder SDJCR

    Lathe turning insert holder SDJCR
    Recommended ✓

    Right holder for inserts / knife for external turning, screw clamping Clamping dimensions: according to the selected variant Designation of the plates that fit into the holder: according to the selected variant Other dimensions - see product description of individual variants. A key for changing the plate is supplied with the goods. The plate is not part of the package, it can be purchased separately. General information on choosing the right holder: Holders type "S" - with screw clamping are suitable for common to finishing operations. They are suitable for smaller material removals. The inserts in these holders have a positive insert back, which enables sharper insert geometries and thus the possibility of achieving a better surface quality. Holders of type "P", "M", "T", "C" and "D" with clamping per inch or clamp are suitable for common to roughing operations - they have higher rigidity. The inserts in these holders have a negative (straight) insert back, thanks to which the inserts do not break out / deform so much and it is possible to roughen them with better and to machine even harder machinable materials.

    from 31,86 € with VAT
  • Lathe turning insert holder SRGCR

    Lathe turning insert holder SRGCR

    Right holder for inserts / knife for external turning, screw clamping Clamping dimensions: according to the selected variant Designation of the plates that fit into the holder: according to the selected variant Other dimensions - see product description of individual variants. A key for changing the plate is supplied with the goods. The plate is not part of the package, it can be purchased separately. General information on choosing the right holder: Holders type "S" - with screw clamping are suitable for common to finishing operations. They are suitable for smaller material removals. The inserts in these holders have a positive insert back, which enables sharper insert geometries and thus the possibility of achieving a better surface quality. Holders of type "P", "M", "T", "C" and "D" with clamping per inch or clamp are suitable for common to roughing operations - they have higher rigidity. The inserts in these holders have a negative (straight) insert back, thanks to which the inserts do not break out / deform so much and it is possible to roughen them with better and to machine even harder machinable materials.

    from 31,90 € with VAT
  • Lathe turning insert holder STGCR

    Lathe turning insert holder STGCR

    Right holder for inserts / knife for external turning, screw clamping Clamping dimensions: according to the selected variant Designation of the plates that fit into the holder: according to the selected variant Other dimensions - see product description of individual variants. A key for changing the plate is supplied with the goods. The plate is not part of the package, it can be purchased separately. General information on choosing the right holder: Holders type "S" - with screw clamping are suitable for common to finishing operations. They are suitable for smaller material removals. The inserts in these holders have a positive insert back, which enables sharper insert geometries and thus the possibility of achieving a better surface quality. Holders of type "P", "M", "T", "C" and "D" with clamping per inch or clamp are suitable for common to roughing operations - they have higher rigidity. The inserts in these holders have a negative (straight) insert back, thanks to which the inserts do not break out / deform so much and it is possible to roughen them with better and to machine even harder machinable materials.

    from 31,90 € with VAT
  • Lathe turning insert holder STJCR

    Lathe turning insert holder STJCR

    Right holder for inserts / knife for external turning, screw clamping Clamping dimensions: according to the selected variant Designation of the plates that fit into the holder: according to the selected variant Other dimensions - see product description of individual variants. A key for changing the plate is supplied with the goods. The plate is not part of the package, it can be purchased separately. General information on choosing the right holder: Holders type "S" - with screw clamping are suitable for common to finishing operations. They are suitable for smaller material removals. The inserts in these holders have a positive insert back, which enables sharper insert geometries and thus the possibility of achieving a better surface quality. Holders of type "P", "M", "T", "C" and "D" with clamping per inch or clamp are suitable for common to roughing operations - they have higher rigidity. The inserts in these holders have a negative (straight) insert back, thanks to which the inserts do not break out / deform so much and it is possible to roughen them with better and to machine even harder machinable materials.

    35,61 € with VAT
  • Lathe turning insert holder SVJBR

    Lathe turning insert holder SVJBR

    Right holder for inserts / knife for external turning, screw clamping Clamping dimensions: according to the selected variant Designation of the plates that fit into the holder: according to the selected variant Other dimensions - see product description of individual variants. A key for changing the plate is supplied with the goods. The plate is not part of the package, it can be purchased separately. General information on choosing the right holder: Holders type "S" - with screw clamping are suitable for common to finishing operations. They are suitable for smaller material removals. The inserts in these holders have a positive insert back, which enables sharper insert geometries and thus the possibility of achieving a better surface quality. Holders of type "P", "M", "T", "C" and "D" with clamping per inch or clamp are suitable for common to roughing operations - they have higher rigidity. The inserts in these holders have a negative (straight) insert back, thanks to which the inserts do not break out / deform so much and it is possible to roughen them with better and to machine even harder machinable materials.

    from 31,86 € with VAT
  • Lathe turning insert holder SCLCL

    Lathe turning insert holder SCLCL
    Recommended ✓

    Left holder for inserts / knife for external turning, screw clamping Clamping dimensions: according to the selected variant Designation of the plates that fit into the holder: according to the selected variant Other dimensions - see product description of individual variants. A key for changing the plate is supplied with the goods. The plate is not part of the package, it can be purchased separately. General information on choosing the right holder: Holders type "S" - with screw clamping are suitable for common to finishing operations. They are suitable for smaller material removals. The inserts in these holders have a positive insert back, which enables sharper insert geometries and thus the possibility of achieving a better surface quality. Holders of type "P", "M", "T", "C" and "D" with clamping per inch or clamp are suitable for common to roughing operations - they have higher rigidity. The inserts in these holders have a negative (straight) insert back, thanks to which the inserts do not break out / deform so much and it is possible to roughen them with better and to machine even harder machinable materials.

    from 31,86 € with VAT

Free shipping

There is possibility of free shipping. For more information click here.

Fast shipping

If on stock, you will recieve your order in 1 working day.

Store

Most of the goods are available at the shop.

Individual discounts

Are you a loyal customer or do you want to become one? Contact us!

Lathe knives and inserts