Drills for bent taps

Product count: 8
  • SK drill for M3 taps, Karnasch

    SK drill for M3 taps, Karnasch

    Carbide drill for drilling bent taps For tap: M3 d1(H7): 2,5 mm Max. depth l3: 10mm Total length l1: 38mm Clamping shank: cylindrical 3 Helix angle: 0 ° C Use up to 65 HRC > Speed(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application : NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. Ä. : 20.1860.0010

    In stock
    28,62 € with VAT
  • SK drill for bent taps M4, Karnasch

    SK drill for bent taps M4, Karnasch

    Carbide drill for drilling bent taps For tap: M4 d1(H7): 3,30 mm Max. depth l3: 14mm Total length l1: 46mm Clamping shank: cylindrical square Helix angle: 0 ° C Use for 65 HRC > Speed(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application : NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. Ä. : 20.1860.0020

    In stock
    28,92 € with VAT
  • SK drill for bent taps M5, Karnasch

    SK drill for bent taps M5, Karnasch

    Carbide drill for drilling bent taps For tap: M5 d1(H7): 4,20 mm Max. depth l3: 19mm Total length l1: 50mm Clamping shank: cylindrical 5-edge Helix angle: 0A ‚ ° Use up to 65 HRC Speed â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0030

    In stock
    36,71 € with VAT
  • SK drill for bent taps M6, Karnasch

    SK drill for bent taps M6, Karnasch

    Carbide drill for drilling bent taps For tap: M6 d1(H7): 5,00 mm Max. depth l3: 23mm Total length l1: 50mm Clamping shank: cylindrical hexagon Helix angle: 0Â ° Use up to 65 HRC Speed(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application : NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. Ä. : 20.1860.0040

    In stock
    39,43 € with VAT
  • SK drill for bent taps M8, Karnasch

    SK drill for bent taps M8, Karnasch

    Carbide drill for drilling bent taps For tap: M8 d1(H7): 6.80 mm Max. depth l3: 23mm Total length l1: 60mm Clamping shank: cylindrical 8 edges Helix angle: 0A ‚ ° Use up to 65 HRC> Speed ??â €‹ â € ‹(for range M3-M12): 1000-1500 rpm rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0050

    In stock
    55,61 € with VAT
  • SK drill for bent taps M10, Karnasch

    SK drill for bent taps M10, Karnasch

    Carbide drill for drilling bent taps For tap: M10 d1(H7): 8.50 mm Max. depth l3: 25mm Total length l1: 80mm Clamping shank: cylindrical 10 edges Helix angle: 0A ‚ ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide < b> Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0060

    In stock
    68,80 € with VAT
  • SK drill for bent taps M12, Karnasch

    SK drill for bent taps M12, Karnasch

    Carbide drill for drilling bent taps For tap: M12 d1(H7): 10,20 mm Max. depth l3: 35mm Total length l1: 80mm Clamping shank: cylindrical 12 edges Helix angle: 0A ‚ ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide < b> Procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0070

    In stock
    100,64 € with VAT
  • Set of SK drills for bent taps M3-M12, Karnasch

    Set of SK drills for bent taps M3-M12, Karnasch

    Carbide drill set for drilling bent taps For taps: M3 - M4 - M5 - M6 - M8 - M10 - M12 d1(H7): 2.5 / 3.3 / 4.2 / 5.0 / 6.8 / 8.5 / 10.2 mm Max. depth l3: 10/14/19/23/23/25/35 mm Total length l1: 38/46/50/50/60/80/80 mm Clamping shank: cylindrical Hexagon < br> Helix angle: 0  ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1865

    In stock
    329,97 € with VAT

Free shipping

There is possibility of free shipping. For more information click here.

Fast shipping

If on stock, you will recieve your order in 1 working day.

Store

Most of the goods are available at the shop.

Individual discounts

Are you a loyal customer or do you want to become one? Contact us!

Drills for bent taps